DRL for Dummies

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 30, 2006
Threads
103
Messages
3,952
Location
Utah
And I'm a dummy. :hillbilly:


I want to install a DRL system in my 80. I like my headlights on at all times, but occasionally forget to turn them off...91's don't have that nifty auto-off feature. :doh:

How would one go about doing this? Yes I searched, but can only find things like "I found a DRL kit and installed it". I've also tried to research ground-switched DRL systems, but no luck there, either. Hell, I even bought a subscription to TIS, JUST to find out how those auto-off systems work. No luck.


SO...


All you Mudder's out there (Canadians, especially), how would you go about installing DRL in a non-DRL equipped 80? Is it possible to retrofit a Toyota auto-off system? Will generic kits work? :confused::confused:

I'm very interested to hear your comments/experiences/opinions...



Thanks
-Lane
 
Last edited:
You can simply install a relay that will turn off the lights when the key is out. Get a volt meter and go to your fuse box located in the DS fender.

With the key OUT check which cables have 12V on them and which have 0V. Ignore the ones that have 12V in that state.

Put the key in and turn it to ACC. Now, from those points that used to have zero volts check which ones have 12V. If you find any, just hook up a small relay that will split the cable which goes from the light switch to the headlight relay. You don't need a strong relay as the cable from the light switch only gives enough power to operate the big headlight relays.
This way, every time you put the key in ACC the relay closes the circuit and makes your headlight switch (by the steering wheel) operable. So if you previously left it in the off position, you will be able to switch your lights on. If you left the switch in ON, they will come on automatically. Either way, when you leave the truck (with your key) the lights will be off.
 
Well, I believe the kit everyone in Canada is the kit I picked up at Canadian Tire 2 days ago. It is called the "Daytime Light System" made by Hamsar model# 70987 and it cost $25 canadian. I found the website for the company: http://www.hamsar.com/drlkits.htm#1, according to the instructions the kit is #45040.
The instructions are simple and straightforward,
1. Ground the blk wire
2. route the white wire to the common wire in the headlight assembly
3. route the yellow wire to the closest parking light positive wire
4. connect the red wire to the positive terminal on the battery.
5. the signal wire is the green wire and they recommend wrapping it around the closest spark plug wire and use that to turn on your lights. You can also simply wire the green wire into a lead that goes hot when the key is in the on position.
I hope to install the kit in the next couple of days, and will post up my install complete with wire colours (for a 94) and pics as a walk thru but my DRL's may not be very permanent.
J
 
Looking forward to the write up and pics as I am also picking up the same kit today!
 
You can simply install a relay that will turn off the lights when the key is out. Get a volt meter and go to your fuse box located in the DS fender.

With the key OUT check which cables have 12V on them and which have 0V. Ignore the ones that have 12V in that state.

Put the key in and turn it to ACC. Now, from those points that used to have zero volts check which ones have 12V. If you find any, just hook up a small relay that will split the cable which goes from the light switch to the headlight relay. You don't need a strong relay as the cable from the light switch only gives enough power to operate the big headlight relays.
This way, every time you put the key in ACC the relay closes the circuit and makes your headlight switch (by the steering wheel) operable. So if you previously left it in the off position, you will be able to switch your lights on. If you left the switch in ON, they will come on automatically. Either way, when you leave the truck (with your key) the lights will be off.

Nice. Crude, but simple. I like it.

However, I'm looking for something that will turn on the headlights, and only the headlights, while the truck is on, similar to later-model Toyotas (Tundra, Sequoia, Tacoma, Cruiser, etc...)

And as for the Canadian Tire thing, they don't have shipping to the US, or any shipping for that matter. Otherwise I'd get that one.


I appreciate the ideas. Keep em' coming.
 
However, I'm looking for something that will turn on the headlights, and only the headlights, while the truck is on, similar to later-model Toyotas (Tundra, Sequoia, Tacoma, Cruiser, etc...)


Just make sure you realize that those systems do not run full power to your headlights during daylight (some run 6 volts, others use a different bulb. . .), dash and tail lights are not illuminated unless headlights are on.

They use a sensor to detect ambient light; when a threshold is crossed, the regular headlights come on.

If you don't add a sensor - remember to turn your headlights on at night:D
 
Just make sure you realize that those systems do not run full power to your headlights during daylight (some run 6 volts, others use a different bulb. . .)

Of course. I'm familiar with the concept, just not sure how the system goes about doing that. :D

...dash and tail lights are not illuminated unless headlights are on.

That's the preferred result. How would one do that?

They use a sensor to detect ambient light; when a threshold is crossed, the regular headlights come on.

Huh, I never thought of that... Kinda like a Chevy/GMC Suburban/Yukon?
 
Last edited:
So I've been racking my brain over this, figuring out where to wire relays and such, when it came to me: Replace the factory headlight relay (SPST) with a DPDT (Double-pole-double-throw) relay.

I'm no good at explaining, so I'm just going to post up the schematics that I drew up.
The first one is just the standard headlight circuit, the second one is the "modified" circuit with DRL.

Thoughts? I imitated the ground switched circuits as best as i can, following the FSM.
headlights_std.webp
DRL_DPDT2.webp
 
Last edited:
Back
Top Bottom