Disc Brake Axel Help Needed

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 11, 2006
Threads
111
Messages
474
Location
Houston, TX
Today I bought a complete Fj40 disc brake axel ($100) that I plan on putting in my 1970. I am really new at this so please answer some very basic questions: 1)The owner did not remember what year the axel came from as it was a spare from years ago. Is there an easy way to tell year for brake parts etc or does it matter? 2) I think my 1970 has 4:11 gears. If this is a late model and has 3:70 ratio, is this a problem? Mainly street use. Light off road. 3) I cannot get the Warn hub locks off. Removed six bolts. Will move out about 1/8 inch. Now what? 4) I have seen Rockauto referenced a lot. Is that best source for calipers and rotors? 5) Any thing else I should know about this swap? Thanks
 
$100??? that was a steal! Good job. The disk brake axles started showing up in late 1975 and on all cruisers in 1976. Most likely it will be 4.11 gear set. to check it, turn the pinon one turn and count the number of turns at the rotor/axle. The hubs have cone washers that can be a bear to get out. Soak them real good with a liquid wrench spary. Whacking the side of the hub with a brass drift and hammer will sometimes pop the little suckers out. Whacking the stud and with brass drift and hammer might also do it, although I don't like whacking studs. Let's us know how it goes.
 
Melloj123 said:
. . . 3) I cannot get the Warn hub locks off. Removed six bolts. Will move out about 1/8 inch. Now what?
There is a "C" clip on the end of the axle stub. When you remove the Warn cover by removing the smaller, allen-head bolts in the silver ring in the pic below, you'll see the stub end of the axle.

warn_hubs.JPG


Since you've already removed the 6 hub mounting bolts, the whole thing will slide right off once you take off the "C"-clip.

Good luck!
 
cardinal fang said:
$100??? that was a steal! Good job. The disk brake axles started showing up in late 1975 and on all cruisers in 1976. Most likely it will be 4.11 gear set. to check it, turn the pinon one turn and count the number of turns at the rotor/axle. The hubs have cone washers that can be a bear to get out. Soak them real good with a liquid wrench spary. Whacking the side of the hub with a brass drift and hammer will sometimes pop the little suckers out. Whacking the stud and with brass drift and hammer might also do it, although I don't like whacking studs. Let's us know how it goes.

C'mon Bill ........Old age catchin up?
ya' know Warns don't use the cone washers.......:confused: :confused:
 
Texican said:
C'mon Bill ........Old age catchin up?
ya' know Warns don't use the cone washers.......:confused: :confused:

Apparently yes!:o I didn't catch the part about them there things on the end of the axle being the Wornout hubs;p All I can say is 2 years before retirement:D
 
im doing a similar swap right now. i took everything from the birfs out from a 60 series (81 or newer i think the discs changed again in 90 or somthing) so maybe go the same rout that i did and take the kunckles, birfs and EVERYTHING apart, wash it and put i back togather that way you dont need to worry about the gear ratio, you will be keeping the original diff. another problem you might run into is the taper in the steering arms (not sure what you need to look for here a buddie hooked me up with the right ones) i dunno if this was any help but...i hope so, good luck with it
 
Back
Top Bottom