Did I just break that?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 25, 2008
Threads
172
Messages
1,666
Location
Opelika, AL
I was having some idle issues with my 94 1fzfe and was told in here to check my air tube to see if there were any cracks. When I was trying to take it off I detached the air box so I could get some separation and got the tube end off near the MAP sensor. When I tried to get the end off near the TB it felt alot tighter so I pulled maybe a little too hard and I felt it give but not in a good way. Well I cracked it. Do you think it was probably cracked already or did I make a mistake in the way I tried to remove it by not grabbing the tube closer to the throttle body?
 
It was probably already cracked, you just made the crack bigger :)

If it was original it was probably time to replace it regardless...
 
While I had to tube off I cleaned the inside of the TB as far an I could reach. Is that good enough or should I take it off to clean it? I also called local Toyota Dealer and new tube was $110 too much? He said I could just duct tape it up for a short period of time.
 
While I had to tube off I cleaned the inside of the TB as far an I could reach. Is that good enough or should I take it off to clean it? I also called local Toyota Dealer and new tube was $110 too much? He said I could just duct tape it up for a short period of time.

That's close to market price IIRC, but it's cheaper from CruiserDan, and you can duct tape it for as long as you feel like having duct tape all over your airtube. I ran it that way for a long time.
 
Spend the money and have your crusier running right. It will save you problems on down the road, especially in the summer when it's hot and your fresh out of duct tape.
 
While I had to tube off I cleaned the inside of the TB as far an I could reach. Is that good enough or should I take it off to clean it? I also called local Toyota Dealer and new tube was $110 too much? He said I could just duct tape it up for a short period of time.

Tape will work short term, just make sure you use enough to seal it up. IIRC Dan's is much better than that.
 
I took my 94 to the oil changer a few years ago. It was taking awhile for them to get it out, in fact they drove it around the parking lot before giving it back to me. When they gave it back to me they said it needed some sort of emission work (can't remember their story exactly) I told them it was fine, paid them and went on. On the way home I noticed it wasn't idleing and died a couple times at lights. When I got home I popped the hood and there was tape wrapped around the tube! I called them on the phone and they said they didn't know anything about it. I drove back and they said they would have to get with the manager but he was out. I left my number and he never called. Anyway, while waiting for them to buy me a new one I took the old one off, cleaned it really well with lacquer thinner and applied a good bead of black silicone. I then taped it to hold it together until it dried. The next day I installed it. I never got the oil changer to admit to anything so I figured I would just leave it siliconed until it breaks. The silicone was still going strong 18 months later when I sold it. I told the buyer it was siliconed and to watch out for it but I bet it is still holding.
By the way, I think I have a good used one off of my diesel conversion if you are interested let me know and I will go see what condition it is in.
 
I took my 94 to the oil changer a few years ago. It was taking awhile for them to get it out, in fact they drove it around the parking lot before giving it back to me. When they gave it back to me they said it needed some sort of emission work (can't remember their story exactly) I told them it was fine, paid them and went on. On the way home I noticed it wasn't idleing and died a couple times at lights. When I got home I popped the hood and there was tape wrapped around the tube! I called them on the phone and they said they didn't know anything about it. I drove back and they said they would have to get with the manager but he was out. I left my number and he never called. Anyway, while waiting for them to buy me a new one I took the old one off, cleaned it really well with lacquer thinner and applied a good bead of black silicone. I then taped it to hold it together until it dried. The next day I installed it. I never got the oil changer to admit to anything so I figured I would just leave it siliconed until it breaks. The silicone was still going strong 18 months later when I sold it. I told the buyer it was siliconed and to watch out for it but I bet it is still holding.
By the way, I think I have a good used one off of my diesel conversion if you are interested let me know and I will go see what condition it is in.



How much for your used one?
 
but it's cheaper from CruiserDan,

Actually, for CJ80, he could get it locally here cheaper than even Dan. I've tried
CJ80, I'll PM you... Join TLCA and our local club and start supporting the local parts counter, Jim and Jeff are great guys over there.
 
Back
Top Bottom