dana300?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 31, 2005
Threads
123
Messages
628
Location
Vidor, TX DIXIE
Anyone use a dana300 from a Scout mated to their stock tranny? I have a 73 cruiser. Was into Scouts or a couple years and had a few spare parts. Also have taken into consideration the rear axle being offset.
 
Welcome.


Are you looking at keeping your three-speed tranny, and trying to hang a dana 300 on the back of it?


Or are you talking about installing a T18/dana 300 combo into a Land Cruiser?


What engine are you using?
 
Anyone use a dana300 from a Scout mated to their stock tranny?

Stock '73 LC3 spd. case is 2.3, D300 is 2.62, so not really a reason to do that unless you'd want a centered rear. I don't even think AA makes an adaptor for this conversion - never heard of one.....

I have a 73 cruiser. Was into Scouts or a couple years and had a few spare parts. Also have taken into consideration the rear axle being offset.

D300's were only offered in Scouts in 1980. What are your long term plans for the rig? I'd grab a short tail D300 from a CJ '80 or '81. There are plenty of upgrade options for this case like a 32 spline ouput, 4.1 gearset, twin stick option. 23 spline input shaft, clocking kits, etc..... But, by the time you add up all these upgrades $$$ you may as well go for the gusto ---> Atlas baybee!
Here's my '80 D300, 4.1 kit, mated to a '67 SM420 via 3.5" Novak adaptor:
 
Last edited:
Like this?



DSCN0012-640.jpg
 
dana300....

Now that i've mopped up the drool from lookin at those atlas x-cases....I have a sbc 327v8, stock everything else. Lookin at my options. My other option is runnin a th350/np205 or 203. More likely option if i decide to swap out. Just wondering my options on the parts available to me now.
 
I was asking if there was anyone running stock tranny with the dana300 "hanging off of it". I have been looking for possible adapters. Can't find any cause apparently noone has one. I'm sure there are better combos, so I'm not too worried about not bein able to use the d300
 
The only one's runnin' a stock hwy geared 3 spd tranny are the purists, resto dudes, dd rigs, or "I don't care if I'm spinnin' my wheels or smokin' my clutch tryin' to git up that trail" dudes. It sounds like you have big plans for the rig. Before you sink a ton of ca$h into it, try it out as is on some medium rated trails & work up some good "seat time" before you jump straight to an Atlas. You'll miss all the in between "good stuff".
 
D300 from a scout is a poor choice, so is the 1980 Jeep D300. 1981+ D300's have the more common output pattern for the rear, more upgrade options because of that...

I've not found any adapters from a Cruiser trans to a D300 either....there are some for minitruck trannies tho.
 
The 1980 Scout D300 & '80-'81 CJ D300's have the "large hole" input & the short tail output. So, they are a better choice than the later long tail versions. You can get just as many upgrades for the shoert tail as the long tail case. Good luck dude!
 
Title the thread "Pimp my Ride" .
 
I was plannin on getting it running the way I like it "as is" first. I think the smart thing after that to do would be mod's in the places i really need em and the only way to really find out that is to wheel stock. Thanks for the replies and I guess I'll get rid of the x-case. I'll be postin a few things on BinderBulletin classified to make shop space for new toy stuff. By the way, havent gotten a name for "it" the project yet. Also, as far as big plans go, I plan on wheeling Gilmer, Katemcy and other Texas trails at first. So Atlas isn't necessary FOR NOW.
 
Back
Top Bottom