Correct Idle Speed?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 13, 2007
Threads
65
Messages
254
Location
Columbia, SC
Been working on my 91 80. I cleaned my mass air flow sensor as well. Once I cranked it up and it idled abt 1500rpm. I lossened the mounting screws for the plug and jiggled it (I had opened it up and sprayed contact cleaner in it) and now I have dropped to abt 1100rpm at idle with the A/C on. When I shift into D or R it drops to abt 700rpm (this has cured my low idle in gear abt 600rpm which caused it to idle rough). I am not unhappy with what I have right now but was wondering what the correct RPM at idles in park should be as well as in gear? I read on a post something abt 650rpm but am not clear if this is in gear etc.

Thanks in advance for your help and this great resource!!!!
 
650 in park with engine warm and A/C off.

Uh,

What exactly did you do to the AFM? I hope you're not saying you loosened the screws at the base of the connector. We've had more than a few folks ruin their AFM's that way.

Curtis
 
Haha. I did. If that is the problem I think I can tweak it and fix it. Yes, when you loosen the screws it will move around and change the idle speed. I will try and tweak it. I know where another is if I need it. Found a 91 exactly like mine (color and everything) I have been robbing at a local salvage yard. Have not gotten that yet so there is one if I screwed mine up.

Thanks for the response. I am def off of 650rpm in park w the A/C off.
 
Mine idles at 960... Throttle cable isn't too tight... Sometimes it'll get down to about 810 when in drive and warm... Timing is advanced slightly, EGR is disabled. Runs fantastic though... What's up?
 
Mine idles at 960... Throttle cable isn't too tight... Sometimes it'll get down to about 810 when in drive and warm... Timing is advanced slightly, EGR is disabled. Runs fantastic though... What's up?

With the truck running, get under the hood and manually close the throttle plate. I'll bet your cable *is* too tight, or is sticking.

Curtis
 
Nothing really. Just idles high in park (1100rpm - 700 in gear). Runs great! EGR and pump disabled. 208K getting abt 12.5. No complaints. Just was not sure abt the idle speed after I messed w the MAF. Not upset just was not sure if I need to try and tweak what I did to it by unscrewing the plug or let her roll!
 
my 96 lx 450 once warm idles at 600 ish ... seems a lil low ? runs kinda rough , never hiccups when I step on the gas, but idling its sounds not so great ...
 
With engine warm, AC off and gears in Park should be 650, when in drive it drops down to 600-620.
 
With engine warm, AC off and gears in Park should be 650, when in drive it drops down to 600-620.

so sputtering sounding kinda while idling is fine then , huh ?
 
so kinda sputtering sound a lil is normal then , huh ?... cause mines 600 at warmed up, no ac in drive at a traffic light , etc.
 
so sputtering sounding kinda while idling is fine then , huh ?


Sputtering is not normal, straight 6 engines are one of the smoothest engine designs. If your engine sputters then you have some maintenance to do. When I first got my 80 it did sputter but after some elbow grease she is a lot smoother now, she only sputters very slightly when in park.
 
Last edited:
its got new wires and plugs , runs better when I put carb cleaner in the tank ... I also run super ... maybe it detonates better on a lower octane than a higher like some motors do ?
 
well and its doesn't sputter too bad , just I notice it and there's no lag when I step on the gas , etc. ... maybe I'm just not used to this motor yet ... only had it for a couple months ...I just had thought 600 rpm seemed low for an idle speed
 
well and its doesn't sputter too bad , just I notice it and there's no lag when I step on the gas , etc. ... maybe I'm just not used to this motor yet ... only had it for a couple months ...I just had thought 600 rpm seemed low for an idle speed


600 is perfectly normal when in drive, mine is just above 600. Flush the oil with cheap dyno and tranny oil couple of times(you can even add seafoam for the last 10-15 miles before change). Take off intake and clean all the ports and replace all the vacuum hoses, make sure your intake system is sealed and have no leak(very common to have cracked intake hose cause engine to be rough). Clean air flow sensor with MAF cleaner.

If you run super you can be more aggressive with the timing advance. I'm all the way to 12-13 degrees with premium/91 gas, runs perfect and a lot more power and torque.

Lots of small stuff to do but you will be amazed how well these old beasts run and how smooth they can be.
 
Last edited:
Cool thanks for the tips !
 
Oh, forgot to add: change or at least do a thorough cleaning if your O2 sensors. It usually gives you additional .5 mpg and slight more power.
 
Back
Top Bottom