Console Removal = $$$$

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 25, 2008
Threads
172
Messages
1,666
Location
Opelika, AL
I'm thinking of building a more useful console for the LC so I took that POS console out and found all kinds of stuff under there. Pens and $$$ were the only things I'd keep though. Didn't have much use for the old gum, used toothpicks:frown:, and sticky spilled drink residue-----sick!!
Do any of you guys have any ideas as far as building materials that are easily worked with or pics that I can use as a guide. :idea:
I'm going to use my old console as a rough template mostly for the bottom contours to transfer on the building material whatever it might be. Probably get a leather covered top from cruiserparts.net.

:hhmm:
 
Found some wires under the console that looked like they hooked up to some type of accessory. Heated seats or power seats maybe?

I've seen posts in the past with pics of some of the wiring under the console. I can't recall what the consensus was on what was what other than most confirmed the optional cell phone wiring was under there.
 
I've been thinking on this also. I got an HF sheetmetal brake recently, and I'm thinking of going with aluminum & rivets. MDF is ok, but if not sealed well you could have issues with moisture. And on something as narrow as the center console, 1/2" minimum on each side seems like alot of space to waste.

But my plans haven't gone beyond the daydreaming stage just yet. And may not for awhile.
 
I've been thinking on this also. I got an HF sheetmetal brake recently, and I'm thinking of going with aluminum & rivets. MDF is ok, but if not sealed well you could have issues with moisture. And on something as narrow as the center console, 1/2" minimum on each side seems like alot of space to waste.

I've been thinking the same thing about sheet metal vs. wood. Wood being the easiest for me to work with because I have the tools to do so. Aluminum wouldn't be bad if I had some way to make a lip, so that it could be riveted.
 
I've been thinking the same thing about sheet metal vs. wood. Wood being the easiest for me to work with because I have the tools to do so. Aluminum wouldn't be bad if I had some way to make a lip, so that it could be riveted.

Harbor Freight Tools - Quality Tools at the Lowest Prices

I haven't used it alot yet, but I've been happy with it in bending some flashing. Intending to get some AL sheet and try it out. Not bad for $60
 
There's a product called Starboard used in the marine industry that's a plastic that cuts and works easier than wood. Check out West Marine. It's not cheap. I've used it with excellent results but I don't think you can paint it, though.

DougM
 
A .50 cal ammo box worked great on a console I made for my old CJ8. I bolted a padded top I made to it that made a sweet armrest. Then I found a dual metal cup holder (think it was "tuffy" brand) and bolted that to the front of the can. I think I was in to it for around $35 by the time I was done.
 
the Harbor Freight break won't do 16 guage, it says it will but definatly not, i've gotten as far as rough sketches, detailed designs of some of the engineering problems that have popped up, and am almost finished with the complete set of drawings. Once those are done i will transfer them to autocad (i know i know more owrk for myself if i'd done AC first but the last time i used AC was back in 88) I'm going to build a engineering model for a test from those designs, more than likely out of cardboard. If that goes well then i'll have a fab shop cut the pieces and do the breaks. Assembly will be done by myself as well as finishing etc. It may not be as cheap as some of the other suggestions but i feel it will be worth it. If you do a search you can find one of the early versions of my sketches. locking OEM console.
 
There's a product called Starboard used in the marine industry that's a plastic that cuts and works easier than wood. Check out West Marine. It's not cheap. I've used it with excellent results but I don't think you can paint it, though.

DougM

X2 on starboard. I'm not sure on painting it, but it does come in a few limited colors you may be able to work with. Any woodworking cutting tools will work fine with it.


King StarBoard XL
 
Back
Top Bottom