Coming off the hip

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 9, 2006
Threads
101
Messages
513
Location
Alpharetta GA
Well it is finally time. I have put if off long enough. I was tired of hearing my roaring decel noise on a short hwy trip so I finally pulled my front shaft and have been driving a week like that and the noise is completely gone. Also when I did this I noticed my birfields are leaking even worse. So off to the driveshaft shop for the front shaft balance and phase and I am ordering the complete front reseal/rebuild kit from Cdan with 100 series rotors and pads. My question is this, in November I am ordering my lift and tires and gears. Should I wait to rebuild the front seals when I regear it or will it really matter? Is there any helpful advice when doing this. I have gone through all of the old threads for the most part. I will be probably trying to get it done on a Saturday with one of my tech friends helping in the shop. It has been at least 3 years since I did my mini's front reseal and it was a pain in the :censor: and I know the cruiser is probably a little harder. Wish me luck!
:cheers:
 
You don't need a reseal kit to pull the axles/diff. You will have to pull the axles again when you do the diff, but it's not nearly as much work as a knuckle job. You don't need to replace any seals, other than the diff gasket.

-Spike
 
Ok, that is what I thought. Thanks for the input. Just trying to break up the costs a little so I don't have to absorb it all at once.
 
If it's only about costs, buy a gearset today, buy another in a month, and buy the knuckle seal kit when you're ready to do the job. Obviously it makes sense to do the gears when you do the knuckles, but if the knuckles can't wait it can be done seperately. If you do them at the same time you can pull the diff and send it out to be set up while you clean up the axle. Of course, that's gonna take longer than a Saturday, and especially if you're setting up the gears yourself. Another option might be to leave the axle shafts/birfs out when you do the knuckles. Then when you're ready to do the gears you just pull the diff, cover the hole, and get the gears installed at your leisure. You'll have to pull the knuckles to install the axles/birfs when you're ready to reinstall the diff. With that method your downtime can be reduced, as you can drive the truck without the front diff.

Of course, it's gonna be challenging to re-gear both diffs at the same time and still drive the truck. :D

-Spike
 
I might end up just trying to do it together but the birfs are pretty bad. I guess I can live with 2wd unitl I have all the funds:frown:. Can anyone say new credit card with 0%!:cheers:
 
"I am ordering the complete front reseal/rebuild kit from Cdan with 100 series rotors and pads."


You only want the pads. Rotors for the 100 will not fit the 80.
 
I just went through this and I can say emphatically that you should do them at the same time. Pull it apart send out the diffs, clean up the axle install new knuckle bearings, races and seals. pre arrange with the gear installer to have a quick turn around.

get some help putting the diffs back in as it is hard to bench press the rear diff and get it on the bolts without ruining the gasget. good luck
 
"I am ordering the complete front reseal/rebuild kit from Cdan with 100 series rotors and pads."


You only want the pads. Rotors for the 100 will not fit the 80.


Really? When I was ordering pads from CDan, I advised I had read a lot about going to the 100 pads for my 80. I thought Dan told me that to do 100 pads, I needed 100 rotors......is the reason I ended up ordering the 80 pads, as I didn't need new rotors. Hmm.....if that's not the case, why did I end up getting 80 pads......:confused: I'm new to all of this, so I'm sure the confusion is all mine.
 
Really? When I was ordering pads from CDan, I advised I had read a lot about going to the 100 pads for my 80. I thought Dan told me that to do 100 pads, I needed 100 rotors......is the reason I ended up ordering the 80 pads, as I didn't need new rotors. Hmm.....if that's not the case, why did I end up getting 80 pads......:confused: I'm new to all of this, so I'm sure the confusion is all mine.

Dan typically recommends *new* rotors (80-Series) when first moving to 100-Series pads. The reason is the wear pattern on the old rotors will not be optimal when using the larger 100-Series pads.

As you were told, the 100-Series rotors will not fit; primarily because they are 5-lug and your wheels (and everything else in the front end) is set up for 6-lugs.

-B-
 
Appreciate the feedback. It's now all clear to me, and makes sense.
Aloha, Joe
 
I have a quick dumb question before we close this chapter... if the 80 series pads have no room to spare, how much bigger can the 100 series pads be and still fit in 80 calipers?

-Spike
 
When fitting new 100-Series pads to new 80-Series rotors, most have to remove the anti-squeal shims. Some choose to grind down the pad. Some claim to be able to fit new 100-Series pads with the anti-squeal shims. Others choose to drive it without the shims for a few thousand miles, then put them back in after the pads have worn down a little. Mine are shimless.

-B-
 
So, the size difference is in the thickness. Gotcha. :D

-Spike
 
Great info! Is there a noticeable difference in braking when going to the 100 series pads? My pads now are aftermarket and only about 20% worn but I figured while I had it all off I would go new everything if it makes much a difference.
 
Back
Top Bottom