Code Help

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 10, 2006
Threads
44
Messages
420
Location
Okefenokee, GA
I just got my 80 back from the dealership to read a CEL code and it came back as Code 117 and I was told that I need to replace the entire EGR system.

I've been reading the archives and I've seen that EGR is code 71...can anybody confirm/deny this?

I really am not looking forward to spending $800+ at the dealer to get this fixed so any insight would be extremely helpful.

Thanks,

Stephen
 
For pre-OBDII (91-94) Code 71 is EGR. They've likely told you to replace the entire EGR system because it can be time consuming to troubleshoot and they're too lazy to figure out which individual component is the issue.

Although it's time consuming it's not hard. You can easily do it yourself with the info on 'mud.


My 94 FSM does not list a "117" code. There are plenty of EGR threads out there. Here's an easy one that worked on my 94.

https://forum.ih8mud.com/showthread.php?t=115298&highlight=code


Please don't spend $800 at the dealer. We'll help you fix it!
 
Last edited:
You could have done it yourself in less than a minute...

When the CEL is on, open the grey plastic lid labeled "Diagnostic" attached to the pass side of the firewall. Turn the key to "ON" but don't start it and have an assistant, preferably a hot one, sit in the driver's seat and watch the CEL. On the inside of the Diagnostic lid you'll see a map showing which terminal is which. Bend a paperclip to connect holes TE1 and E1. The CEL will blink to show you which code. Code 71 would be seven blinks, a pause, and then 1 blink.

If the dealer cleared the codes this won't work and you'll have to wait for the CEL to come back on. To clear the codes yourself pull the 15A EFI blade fuse for 1 minute -- it's located in the fuse block under the hood. Pull the fuse not the relay.
 
When the CEL is on, open the grey plastic lid labeled "Diagnostic" attached to the pass side of the firewall. Turn the key to "ON" but don't start it and have an assistant, preferably a hot one, sit in the driver's seat and watch the CEL. On the inside of the Diagnostic lid you'll see a map showing which terminal is which. Bend a paperclip to connect holes TE1 and E1. The CEL will blink to show you which code. Code 71 would be seven blinks, a pause, and then 1 blink.

If the dealer cleared the codes this won't work and you'll have to wait for the CEL to come back on. To clear the codes yourself pull the 15A EFI blade fuse for 1 minute -- it's located in the fuse block under the hood. Pull the fuse not the relay.

MoJ...Fantastic--I'll definitely use this next time.
 
For pre-OBDII (91-94) Code 71 is EGR. They've likely told you to replace the entire EGR system because it can be time consuming to troubleshoot and they're too lazy to figure out which individual component is the issue.

Although it's time consuming it's not hard. You can easily do it yourself with the info on 'mud.


My 94 FSM does not list a "117" code. There are plenty of EGR threads out there. Here's an easy one that worked on my 94.

https://forum.ih8mud.com/showthread.php?t=115298&highlight=code


Please don't spend $800 at the dealer. We'll help you fix it!

Great info MoJ--I'll be trying that tonight.
 
Oke, here is a list of the codes for OBD 1 vehicles

http://www.troublecodes.net/Toyota/

I am in the process of clearing my code 71 (start with new modulator - Thanks Dan - cleaning the throttle body and changing as many vacuum lines I can get to).

I have had the CEL on for the year and a half I have owned the vehicle and have not experienced any problems from it. I am just tired of looking at it or the business card that I put in front of it :doh: .

Riley
 
Back
Top Bottom