Chev Auto chassis conversion question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 6, 2012
Threads
2
Messages
6
Location
Forbes, Australia
Hi All,


I have spent the last 12 months stripping down my 1981 FJ45 Ute (RHD) for a full rebuild and chev & auto conversion. I am hoping to put in a TH700 behind the chev and have read that with an adaptor behind the transmission onto the transfer case, the whole lot will shift the transfer case back approximately 170mm. Just wondering if anyone who has done this conversion had to move / alter the cross member on the chassis behind the transfer case or possibly lose the hand brake on the back of the transfer and convert to rear hand brake on the drums (eg 60 series brakes on rear axle). any assistance appreciated, cheers.
Chassis2.webp
 
I've done a number if these conversions; it's what I do for a living.

If you haven't purchased any of the adapter parts yet, then I'd suggest this:

Move the transmission cross member back. The best way to do so is to install another cross member just forward of the rear spring hangers. Weld a couple of scab plates to the frame and then weld the new cross member in place. You'll want it to have a curved portion allowing for drive shaft clearance. We usually put two 45 degree bends at the ends so the entire cross member offers more clearance.

Also, did your ute come with a split case or the earlier one-piece t-case? The split case is a much better choice because its stronger, quieter and offers more clearance between the transmission and front drive shaft.

Changing the rear axle to a 60-series brake setup is a great upgrade.

Georg @ Valley Hybrids
 
Before you modify the rear cross member.......... Take a quick measurement from the front shock tower to the cross member. I don't recall if the cross member is in the same location as on a 40. If it is, it'll need to be moved.

If you do move it, weld in the new cross member first and then cut off the existing unit. That'll help keep the frame square.

Georg @ Valley Hybrids
 
Thanks guys for your prompt reply. I measured the distance from the balancer / pulley on my 2F to the back of the transfer when I had it in. I then measured up the chev specs, auto, and transfer case with an assumption on an adaptor and the story didn't look good. I was hoping to get away with it but I don't think I will. Im going to ring a mechanical engineer here in oz and get some advice also because these conversions are getting harder to do and get passed for rego, but being pretty sure I will have to do it Ill ask him what he would require to pass it first so I don't hand it in for inspection and get knocked back only to have to modify more. The cruiser came with the split case which I will definitely keep, and I can get my hands on some 60 series brakes so I think Ill just go down that path to. Im a bit unsure about taking the handbrake off the back of the transfer and how I set up the drive shaft, also brake cables to rear but ill get to that step as the build goes along. Im about to sandblast everything and POR15 paint all the chassis and diff housings and everything so Ill try and start a thread on the build when it starts to go back together and starts looking good.
Again thanks very much for the advice as it helps set me on a more definite path.
cheers
Andrew
 
If you use a rear axle from an FJ60, then use the ebrake cables as well. The handle and bucket can be grafted into your cruiser fairly easily. We've done it that way; works great.
If you want to run the stock width 40-series rear axle, then get one from a late 40 or 45. It'll have the same brakes as a 60. You should be able to find a FF rear if that's what you're thinking about running.

Converting the Tcase to a standard rear yoke is fairly simple. You'll have to change the output shaft, speedo housing and rear flange. The Tcase ebrake parts are desirable so if you take them off, let me know. I'd be interested in buying them from you.

Georg @ Valley Hybrids
 
Righto cheers, I have access to a 1984 60 series wagon sitting in a yard and my FJ45 is Late 1981 so hopefully alls good, Ill keep the 40 series rear axle if I can and just convert the brakes. Itll be a while with the build but Ill remember when I start with engine and gearbox on the parts if your interested. Ill take the whole ebrake set up out of the 60 and see how I go.

Again thanks Georg, advice appreciated.

Andrew
 
my FJ45 is Late 1981 so hopefully alls good, Ill keep the 40 series rear axle if I can and just convert the brakes.


Ill take the whole ebrake set up out of the 60 and see how I go.


I don't know if both your axles are semi float or full floating, if they are full floating there are 4 bolt and 8 bolt brake backing plates so you might want to check that they match
 
Back
Top Bottom