Chasing electrical gremlins

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
May 15, 2018
Threads
4
Messages
24
Location
Grande Prairie, AB
Hey everyone,

Quick background before my issue, my batteries have not been holding a charge and we've hand constant issues of being left dead on the trail the last month or so, getting frustrated I assumed it was either batteries that were no good or an alternator (the belt is slipping, a replacement is incoming) however! that being said, I just finished some gauge installs yesterday, which is where I feel like there is a bigger issue.

I installed a volt meter and an AFR gauge. The volt meter I ran directly to the battery for positive and negative, for the AFR I taped into the dome light fuse with an "add-a-fuse" for switched power and straight to the battery for the constant. It was this time after I had cleaned up everything and humbly IMO made for a really nice install, that I saw the gauges were constantly powered, no key in the ignition, constantly on.

So I'm feeling like maybe somewhere there is a hot wire or a messed up ground somewhere (I know my connections are good for the gauges). I've wired up other gauges in cars before and I've never had this issue before- there is a bunch of other mods from the previous owner so I fear it's just a matter of tracing all of his leads and looking for a missed ground or something... it's all I can really think of- I can't think of another reason why I'd have such a parasitic draw and constant power- and these gauges shouldn't be on without power (of course). I'm watching MrMoMo's excellent electrical videos but thought I'd see if anyone could bounce some ideas off me, if I am just overlooking something super easy...

Thanks!
 
With a battery switch, you mean like a master kill switch? I'm running dual batteries so could I run a single one off the primary battery or should I run one switch per battery.

Thanks for the idea!
 
With a battery switch, you mean like a master kill switch? I'm running dual batteries so could I run a single one off the primary battery or should I run one switch per battery.

Thanks for the idea!
depending on how you set it up, you can use one switch to kill the entire system. blue seas has diagrams on how. how is yours wired up? are the parallel or are they isolated?
 
They're parallel, just the stock dual battery setup from Toyota, I should mention it's a 1HDT JDM 80 series. I'll have to check out Blueseas as well
 
Yeah 24v. My rookie brain understanding is that it needs 18v to start, otherwise just a parallel 24v system.
not parallel, its series then if its 24v. first off I would check to see if both batteries are good. test each one individually (disconnect them) with an actual battery tester not a multimeter. you want to test the cells in the batteries for a dead one. reason being you can still read voltage as being over 12 (per battery) and have a bad cell. and if one is bad change both.

what kind of batteries are you running?
 
Apologies! the batteries are reading 11.4 and 11.8 volts. I'm running North Star, they're around a year old. Paid way too much for them so I'm really hoping they're not dead. When I have time I might do what you suggested and pull all the accessories. It's just really strange to me that these gauges would be constant on even without the key in.
 
I'm pretty sure on the diesel 80's, it is a 24V system (2 batteries in series) to start and then solenoids switch the batteries back to a 12V system (2 batteries in parallel).

When you say gauges are constant on - is that the gauges you added or the OEM vehicle gauges or both?

Besides fixing your slipping belt and load testing the batteries, I'd suggest you need to measure the parasitic current draw when everything is in its nominal 'off' mode. Multimeter on amp range in series with the 12V main feed. Or if you have a decent and sensitive DC clamp meter you can measure the various battery power leads to identify the various current draws while 'off'.

If your batteries are truly 11.4 and 11.8 then they are flat and discharged. What kind of meter are you measuring with?

cheers,
george.
 
Brilliant thank you! they're aftermarket gauges, an AFR and a Volt Meter (installed ironically because the batteries kept dying) I pulled them and tested them with my booster pack that has a tester, whether this is accurate or not I'm sure can be discussed, I don't have a different battery tester. The OEM gauges are off no problem, when the batteries die it's that they don't have the cranking power, every time I've needed to boost, I've had accessory power (lights/radio etc.. all comes on) just not enough jam to start (or turn over for that matter. So obviously I'm not getting the 18v for cranking the starter)

Thanks both for your ideas and input, really appreciated so far!
 
Back
Top Bottom