Can 02 sensors be maintained??

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 2, 2003
Threads
214
Messages
3,454
Location
Rockville, MD
Ok, I replaced my O2 sensors about 2.5 years ago(~60k miles ago). I'm getting a code 21(Heated O2 sensor, Heated O2 sensor circuit, or ECM are the problems listed in the FSM).

Is there anything to do here besides replace the O2 sensors? I haven't gotten a chance when the truck was actually cool to crawl under there and make sure the O2 sensors' wires are not getting hot(I presume that's what 'Heated O2 sensor circuit' means), but assuming that's not it, I'm thinking I need to do something w/ the O2's themselves.

BTW, this code came on after I ran 2 cans of seafoam through the engine about 2 weeks apart(this was about a year ago). Yeah, yeah, I know I'm a bit behind on my diagnosis.

Thanks,

Ary
 
Arya, Would you mean pulling them and somehow servicing and / or just cleaning them? If so I would like to know the answer to that question as well. I wouldn't think it is possible but who knows. I know that the protective loom that sits down there does become damaged or rotted after so many years so checking for heat may be part of it but even with mine almost completely gone prior to replacing my whole Engine wiring harness I never threw a code. I have read many places where simply by replacing the o2 sensors people have gained gas mileage, hence my novel idea of "if they could be cleaned"?
 
Yes, cleaning is what I had in mind. Somewhere once upon a time someone explained to me that O2 sensors are like batteries and they have a certain life span. Since I don't think the life span of mine is up, I thought there might be some way to clean them to restore function. Alas my knowledge of O2 sensors stops there, so I don't know if it's really feasible or not.

Ary
 
Many fuel additives and injector cleaning additives will state on the bottle if they are safe for use with O2 sensors. Many products are not, and that can have a negative effect on the life of your sensors. I don't have a can of Sea Foam available to me right now to even see if it says anything about being "O2 sensor safe" or not.

From the sounds of your code though, this may not be the reason for your problem. The O2 sensor has a resistive heater built into it to help it get up to operating temperature faster. If this heater fails, then it will throw a code like you describe. You should be able to unplug the wire harness and check this with an ohmeter. I think the FSM gives the range of resistance for a good sensor heater.
 
Many fuel additives and injector cleaning additives will state on the bottle if they are safe for use with O2 sensors. Many products are not, and that can have a negative effect on the life of your sensors. I don't have a can of Sea Foam available to me right now to even see if it says anything about being "O2 sensor safe" or not.

From the sounds of your code though, this may not be the reason for your problem. The O2 sensor has a resistive heater built into it to help it get up to operating temperature faster. If this heater fails, then it will throw a code like you describe. You should be able to unplug the wire harness and check this with an ohmeter. I think the FSM gives the range of resistance for a good sensor heater.

Seafoam won't affect the heater circuit, only possibly the signal circuit (contaiminated 02 - will come up out of range lean/rich, or slow)

The heater circuit is only the element inside the sensor that keeps it at the proper temp. I agree that cking with an ohm meter to make sure you have a complete circuit is key. I suspect you either have a bad connection at the harness, or a broken wire to the circuit, or the heater element itself failed.

HTH

Scott Justusson
94 FZJ 80 Supercharged
 
Back
Top Bottom