Came down hard- body damage?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 8, 2008
Threads
25
Messages
110
I convinced myself not to take off my spare or tow hitch when I hit the mud the other day :o. Sheer inexcusable laziness, now I'm kicking myself. You can probably see where this is going... haha well long story short, i came down hard on the spare/ hitch on top of a dirt berm. The spare carrier is tweaked and there was enough force to shove the spare into the aluminum step on the rear bumper which is bent now too. The thing that has me worried is that the tailgate is slightly offset. It still closes but with some effort. Does this sound like I actually bent the body with the spare's impact?
 
After reading this twice, I assume you have a spare tire carrier with the stock bumper? IIRC the spare swingout on the Kaymars connects into a support installed in the plastic bumperette- is this the type of spare carrier you have? Let's have some more details on your spare tire carrier setup and let's see some pics. BTW- welcome!
 
He has to unless someone took it out and welded the spare mounts directly to the body, which I honestly can't see anyone doing.

With a hitch it's going to be *REALLY* hard to tweak anything if that's what got hit. I've whacked my port installed hitch pretty hard plenty of times with no bending (except the two tabs where you hook your chains to, which are tweaked). I don't think he hit his hitch, at least not directly.

Honestly I'm having a hard time thinking of what he could have hit that would cause this. As Hayes said the spare crossmember is going to take a LOT of punishment before it'll bend far enough to hit the body, and it's far enough back that I can't imagine it'd cause the tailgate to tweak.

The only thing I could think of that'd cause that much damage is hitting the rear quarter panels, which could tweak the body around the tailgate. Either that or a bent frame, but that'd have to be one heck of a hit.



Pictures would probably help a lot.
 
I convinced myself not to take off my spare or tow hitch when I hit the mud the other day :o. Sheer inexcusable laziness, now I'm kicking myself. You can probably see where this is going... haha well long story short, i came down hard on the spare/ hitch on top of a dirt berm. The spare carrier is tweaked and there was enough force to shove the spare into the aluminum step on the rear bumper which is bent now too. The thing that has me worried is that the tailgate is slightly offset. It still closes but with some effort. Does this sound like I actually bent the body with the spare's impact?


I've got my spare currently mounted on my Kaymar and left my stock spare mount in place, so I've got a clear view of what we're talking about. There is the main body structural support just aft of the stock spare mounting holder and not far above it. If that is what has been tweaked, and I would bet money that it is, it would explain your problems. The bar that Hayes is refering to is prolly just one of the casualties underneath. Your weather seal on the tailgate has prolly been tweaked, to say the least, also. I'm sorry to have to say this, but you've prolly learned an expensive lesson. True, the stock spare mount is stout, but it's not stout enough to support that kind of weight. When you add the possibility of the spare being loosely tightened on mount, it could easily flex into the body when coming down hard like you describe.
 
I've got my spare currently mounted on my Kaymar and left my stock spare mount in place, so I've got a clear view of what we're talking about. There is the main body structural support just aft of the stock spare mounting holder and not far above it. If that is what has been tweaked, and I would bet money that it is, it would explain your problems. The bar that Hayes is refering to is prolly just one of the casualties underneath. Your weather seal on the tailgate has prolly been tweaked, to say the least, also. I'm sorry to have to say this, but you've prolly learned an expensive lesson. True, the stock spare mount is stout, but it's not stout enough to support that kind of weight. When you add the possibility of the spare being loosely tightened on mount, it could easily flex into the body when coming down hard like you describe.
[/FONT][/SIZE]

You make a good point about the rear cross member causing the damage. I don't think think that the spare hitting it could do that much damage however, at least not without absolutely destroying the spare.

It would take a pretty strange shaped rock to hit that cross member and not the tow hitch or spare (both of which would absorb a lot of the impact first. That cross member is pretty well tucked up in there, and if you have a stock spare and a factory hitch there's lots of stuff that will be hit long before that cross member is.


Anyway, regardless of what hit and caused the damage I can only see two scenarios causing that much damage.

1) Jumping
2) Speed, and lots of it.
 
i did the same thing when i first got my 80. Went wheelin' with the spare underneath. Ended up putting a HUGE gouge in my wheel and cut a 4 inch slice in the spare tire. Ouch.
 
Here's the damage

Thanks for taking interest guys:cheers:. I was at the dealer today ordering a new seal for my dizzy and brushes for the alternator and misc stuff. They quoted the rear structural support at $240 but it looks like it would need to be welded in?

bent plate
DSC00713.jpg



this is where the structural support got hit/bent, the mangled thing is a guide for the spare tool when lowering the tire.
DSC00712.jpg



spare carrier left
DSC00715.jpg


spare carrier right
DSC00714.jpg


side view of bent support
DSC00717.jpg


these two plugs were also missing, not sure if this is related to the impact, but it allowed a good amount of mud and water to get into the side panels and come out my speaker grate:mad:
DSC00716.jpg
 
Wow. That's an amazingly hard hit, and you had some incredibly bad luck there.

Definitely hit the spare. It looks like the rear cross member got hit pretty dang hard.

Just how fast were you going? :eek:



The new rear cross member will need to be welded in. Frankly the price the dealership quoted you seems way too low to me. Get the frame checked to make sure it's still straight, if the cross member bent that much there's a fair chance that the frame is no longer straight.
 
That must of been quite a jolt. I am a bit baffled at how the crossmember was so affected despite the presence of the hitch.

Maybe the dealer is quoting for straightening the crossmember rather than replacing it. Depending on your damage, a frame shop may just attach it to a rack and tweak things back to home.
 
i would not worry about that at all. Get a real big, fat guy to jump up and down on the bumper a bit to straighten it. Then, use this as the perfect excuse to get a rear bumper with tire carrier.
 
You'd be suprised how thin and whimpy that rear crossmember is. Perfect timing to chop it off, ditch all the rear plastic bumper pieces and corners, plus cut 3.5" of your frame and fab a custom bumper out of lightweight 1.5" tubing:D. Oh, and ditch your spare tire crossmember and put the tire inside on a home-made or Slee internal tire mount.:D
 
Aftermarket rear bumpers

I've been cruising the forums and the crossmember looks expensive. Is there an aftermarket bumper that just replaces it?
 
I've been cruising the forums and the crossmember looks expensive. Is there an aftermarket bumper that just replaces it?

There is Hanna's which does, but that's a wait....

Other than that, pretty much custom...
 
4x4Labs rear bumper also replaces it.
 
Back
Top Bottom