brake boosters/master cylinders

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 18, 2004
Threads
259
Messages
1,501
Location
Pacific Northwest
So my brakes are bringing the suck.:shotts:

....replaced the rotors from American Toyota
....front pads are the 100 series from Dan
....Rear pads are 80 series from Dan
....Bled the system and replaced with new brake fluid
....frame to body are Slee braided stainless lines

The peddle is very mushy. What direction should I go from here? I have done the master cylinder test and it holds fine. Could it be the brake booster? My new brake stuff has about 1,000 miles. The cruiser is a heavy 94 w/ 164k
 
Have you bled the rear proportioning valve?

X2 If you have I would re-bleed everything then if that doesn't do it I would replace the master anyway. I doubt it's the booster.
 
X2 If you have I would re-bleed everything then if that doesn't do it I would replace the master anyway. I doubt it's the booster.

I will try this again with another batch of new fluid. The old fluid was ugly. It may very well be the proportioning valve.
 
How did you break the brakes in?
How did the calipers look?

Can't remember who but somebody posted a break in procedure here on mud. I printed it out and did exactly that as soon as I was on the road. The calipers look to be in good cond.
 
Happened to me; actually hit someone in the rear bumper when I lost my pedal pressure.

I replaced the master cylinder; problem solved. Apparently they can do some sort of internal
bypass thing particularly during panic stops, then you lose the pedal and hit something.

g
 
Question about the pads;
I was not aware that you can use 100 series pads on the front;
what type of pads are these and where do you get them??

I was going to switch to Hawk brand ferrocarbon brake pads;
any thoughts or experience with those?
 
Question about the pads;
I was not aware that you can use 100 series pads on the front;
what type of pads are these and where do you get them??

I was going to switch to Hawk brand ferrocarbon brake pads;
any thoughts or experience with those?

Mud wisdom dictates Toyota pads are best. Search in the 80 section for 100 pads. I bought mine from Dan at American Toyota in New Mexico....he gives all the guys on mud a smart shopper discount. He knows a thing or two about Land Cruisers as well:lol:
 
yeah, i have had the same problem with my 91, and have so far put 2 reman'd master cylinders and 2 reman'd calipers on it, bled it countless times and made sure to hit the lspv, no luck. my front brakes = the sludge and it seems that the only stopping i am getting is from the back brakes. when i bleed the lspv and the front brakes there is no pressure, and fluid only comes out in a slow trickle. anyone got any more ideas here i would appreciate it too.
 
yeah, i have had the same problem with my 91, and have so far put 2 reman'd master cylinders and 2 reman'd calipers on it, bled it countless times and made sure to hit the lspv, no luck. my front brakes = the sludge and it seems that the only stopping i am getting is from the back brakes. when i bleed the lspv and the front brakes there is no pressure, and fluid only comes out in a slow trickle. anyone got any more ideas here i would appreciate it too.

Wow, that's really dangerous; especially on slippery surfaces that back end can completely flip around! It sounds like you might have a bit of blockage from debris or dust or rust inside your front lines you might want to loosen them one at a time and really stop on the brake with the engine on you might develop enough pressure to push that crap out. BTW, unless it is a Toyota reman, I would stay far far away from the McParts reman stuff - lessons learned the hard way with my old 4Runner. HTH (Hope That Helps). :cheers:
 
Wow, that's really dangerous; especially on slippery surfaces that back end can completely flip around! It sounds like you might have a bit of blockage from debris or dust or rust inside your front lines you might want to loosen them one at a time and really stop on the brake with the engine on you might develop enough pressure to push that **** out. BTW, unless it is a Toyota reman, I would stay far far away from the McParts reman stuff - lessons learned the hard way with my old 4Runner. HTH (Hope That Helps). :cheers:

OI to that, i called a local mechanic shop that is reputed to do the best work on all imports next to dealership work, and they basically said that they didn't have to look and that the prob. was the reman'd MC. another thing is that alot of rust seems to come out at the lspv, so perhaps forcing out the shiite will do the trick. More to Come.

Tom
 
Back
Top Bottom