Booster required?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 25, 2005
Threads
41
Messages
156
Location
Bradenton, FL
Considering a front disc conversion, but was wondering if a booster is required for the new brakes to work. I am already accustomed to mashing the crap out of my brakes and it really doesnt bother me, just tired of adjusting and the extreme pulling when they get wet......which is often.
 
If you are "mashing the crap" out of the brakes to stop there is something wrong with your drum brakes. The stock vacuum assist booster works very well when everything is right.

That said, the front disk conversion was one of the best mods I ever did on my rig. I did the mini truck knuckle conversion at the same time. I used the stock Master cyclinder, all I did was remove the residual pressure valve from the front line supply fitting. If you have a single supply line you will need a proportioning valve. IIRC disk brakes only require 2 PSI residual pressure compared to the 10 required for drum. I have no problem stopping with the new set-up.


I plan on asking Santa for the stuff to do the rear wheels. ;)
 
Different manufacturers use different amounts of boost. I think the trend has been to reduce the master cylinder piston diameter and compensate with more vacuum assist. It was common on late '60s MGs, for example, to remove the vacuum booster (which often failed) and run without it. It was possible to generage enough pressure manually, although the pedal effort was pretty high.

Maybe you can disable the booster temporarily on a '70s or 80s vintage truck with front discs and rear drums and see what it feels like? Bet you won't like it. ;)
 
When I say I mash the crap out of them I mean as compared to power brakes. I have no booster at all so there isnt one to leak, so the harder I push the more bite I get. So if I am creating 10psi with only my foot, 2psi should/would/could be possible and easier? My brakes have been totally rebuilt with all new wheel cylinders, shoes and drums turned and were adjusted properly (it stops good and straight when dry). One reason for my original question is that since my 40 is a diesel, there is no available vacuum unless I change my alternator to one with a pump. One more thing to buy on top of a booster (if needed).
 
Electric vacum pump

I installed an electric valcum pump on my Fj40. I was tired of stalling it on steep inclines because of the card and then run out of vacum. It works like a dream. If I blow the pump I am buying a new one. As long as the key is on I have 18 inches of vacum. THat you suit your diesel and you could end up with a far better breaking system. Man-a-fre sells a GM conversion master cylinder with double diaphram booster. I am looking at that conversion. if you want more info and pictures of the vacum set up email me at FJ40_landcruiser@cox.net
 
Conex said:
When I say I mash the crap out of them I mean as compared to power brakes. I have no booster at all so there isnt one to leak, so the harder I push the more bite I get. So if I am creating 10psi with only my foot, 2psi should/would/could be possible and easier? My brakes have been totally rebuilt with all new wheel cylinders, shoes and drums turned and were adjusted properly (it stops good and straight when dry). One reason for my original question is that since my 40 is a diesel, there is no available vacuum unless I change my alternator to one with a pump. One more thing to buy on top of a booster (if needed).
The vacuum assist is gone?

Is your Master cyclinder mounted to a disk shaped thing about a foot in diameter and maybe 4 inches thick?
 
My brake pedal linkage is attached directly to the master cylinder, then a single brake line comes directly out of the master. There is no booster, totally manual. I know what a booster is and looks like. There is no vacuum as there is no carb, only injectors and a butterfly valve for air intake.
 
Last edited:
Hey guys-
1) He's in Costa Rica.
2) It's a diesel (i.e. vacuum isn't as readily available)



All that said, I just did a 4-wheel disk swap on my 64 FJ40, which had no booster from the factory. I used a 75 Corvette master cylinder which was relatively cheap and came from a car that: a) did not have a booster from the factory; and b) had 4-wheel disk brakes. I have the standard Monte Carlo caliper swap in the rear and minitruck swap up front. It stops perfectly. The pedal pressure is firm, but not any worse than well-adjusted unboosted cruiser drums. I put a proportioning valve inline for the rear, but it stops perfectly on pavement with it turned all the way in (not limiting at all). I haven't tried it out on dirt, and I can still chirp the rear tires if I downshift and brake at the same time, so I may adjust the proportioning valve a bit in the future after some more testing.


So the short story is: Yes. It can be done without a booster.
 
If your 77 has a 7/8" bore MC you could help yourself out by switching to a 1" or 1 1/8" MC from another year vehicle. This will increase your braking power with or with out booster assist.

Birfield.com MC info:

FYI FJ80's and FZJ80's have 1" MC's. choose a MC based on drum or disc rear brakes.

When I swapped FJ60 brakes onto the front of my 74 I noticed it took a lot more pedal pressure to stop the truck.
 
Back
Top Bottom