block heater for 1FZFE?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

txgringo

SILVER Star
Joined
Mar 25, 2012
Threads
101
Messages
1,067
Location
Durango, CO
I've tried searching the forum, but all the results I've seen are really old. Anybody installed an engine block heater on an 80 recently? Any suggestions on sourcing one of these? I'd prefer OEM, but it seems I might sooner find the purple unicorn that my daughter requested for her birthday.

I did find this PDF that references part number "C0140-00134" for this engine.
https://trdparts4u.toyotaofdallas.com/ProdPDF/All-ApplicationChartTOYOTA.pdf
 
yes .. I finally installed mine when I was doing my headgasket (97 lx450) ...what would you like to know?

the part number was C 0140-00134-S2

the block heater is installed in the core hole plug location :

"L.H.S. 1st from the front. Tie cordset with cable ties to power steering pump hose, and then to front pump bracket. Route cordset to front grill.'

That means in the core plug at the front of the block on the DS. I used a small worn chisel and a 2lb hammer and holding the chisel off centre of the plug (in the depressed area of the plug - not on the edge abutting the block) I gave it a solid wack. The plug spun in the cavity and was easy to pull out with channel lock pliers using a small block of wood on the engine block to lever against.

BTW ... dont worry about the "S2" attached to the part number shown above ... that is the part number that was printed on the box from Toyota that the block heater came in. In the instructions provided it references just C 0140-00134. incidentally this is the same part number shown for the 87-91 Camry 3S-FE; 88-91 Corolla GT-S 4A-GE; and 97 Lexus LX450 1FZ-FE... also various years of Celica that use the 3S-FE and 3S-GE engines

Sorry must edit this to add: the heater coil has to be positioned so that it is directed to "12 o'clock" UP when installed
 
Last edited:
I installed a inline heater on the lower radiator hose when I was living in an area that dropped into the single digits. It was cheap and easy. It worked great and if I left my defroster setting open my window would be partially defrosted in the morning no matter how cold it got outside. I only paid about 40 bucks for it too!
 
I think personally that the inline units are a better way to go; in my case, with the head off - I had pretty good access to the frost plug and already had the block heater ... so I went that way. If I was staring at a full engine compartment - I would go inline .. and they may be a better performing unit as well but I have no insight on this one way or another. I understand that big diesels working in the north have a strong preference for webasto heaters ... which are essentially "in-line" units ... but they arent cheap!!
 
I know Milwaukee gets cold, but have you had any issue with it so far? I lived in Northern Idaho for a few years, had a T100 with a block heater and an 80 series without. I didn't notice a difference in performance even on mornings when it was -10F. YMMV, but I'd only run a block heater if it was consistently below zero at nights for weeks at a time, mostly because the benefits of modern and synthetic oils get the job done in all but extreme conditions.

The advantages of an inline heater are a little better as they keep the entire engine warm and you will blow warm air quicker after startup.
 
Somehow I missed all the replies to this thread LAST YEAR... seems I wasn't subscribed to my own thread. Anyway, thanks for the info guys.

I've not had any issues with it not starting up, but on mornings when it was really cold it seems a little slower to crank and each time I hear the "dry whining" sound when I crank it in the cold I cringe a little bit thinking about how many miles of engine life that crank just took from my 80...

I like the idea of the inline heater keeping all things a bit warmer.

@slowLC, what inline unit did you go with?
 
I went with one from autozone, I can't remember the brand but I have had it in for a few years now and it's great! Cheap and easy
 
Back
Top Bottom