Birfs..how do I know when there bad?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 30, 2006
Threads
79
Messages
783
Location
Traverse City, MI
Website
www.myspace.com
I was under my rig (97 TLC, 155k) this weekend and noticed alot of build up around the birfs. Ive done some tight circles while locked and get no clicking. Im assuming they need rebuilding, Im just hoping I can put it off until spring when it warms up. Also, should I wait to change the diff fluid until I do the rebuild?
 
Change your diff fluids. Pull the fill plug FIRST. Then the drain, if the oil is 'thick' and kind of green, then you have grease in your diff oil. This means a rebuild. You can add grease to the knuckle through a square fill plug on top of the knuckle and re-fill the diff w/ new, fresh oil. Don't do any major wheeling and you should be fine. Or find a buddy w/ a heated garage.
 
You're due for a repack at the minimum. If they don't click, they're probably still good. Drain the diff when you do the birfields. There is a lot more you could do, "while you're in there," if you are so inclined.
 
Change your diff fluids. Pull the fill plug FIRST. Then the drain, if the oil is 'thick' and kind of green, then you have grease in your diff oil. This means a rebuild. You can add grease to the knuckle through a square fill plug on top of the knuckle and re-fill the diff w/ new, fresh oil. Don't do any major wheeling and you should be fine. Or find a buddy w/ a heated garage.


When you say "this means a rebuild" do you meen the diff, the birfs, or both?
 
You're due for a repack at the minimum. If they don't click, they're probably still good. Drain the diff when you do the birfields. There is a lot more you could do, "while you're in there," if you are so inclined.

As far as "a lot more you could do", what do you suggest?
 
birf re-build. You can get by with puting in new axle seals, but why you're IN THERE... you might as well replace bearings and other seals.
 
I did a lot "while I was in there."

Front Axle:
Replaced birfields with Longfields.
Replace axles with Longfield axles.
New bearings
New trunion bearings
New seals
New rotors
100 series pads
New fluid
New hex plugs for diffs (all 3 diffs = 6 plugs)
New grease & gear lube (of course)

Rear
Repacked bearings
replaced diff fluid & plugs
new brake pads
De-rusted parking brakes
Replaced broken cast parts on parking brakes

Center
New fluid & new plugs

There were two big headaches. The first involves everyplace there are cone washers. It took two of us about two hours each just dealing with the cone washers. The second was the parking brakes. We spent a few hours just working the rusted bits free before we could even take it appart without breaking more stuff.

Now one truck is done with the above... One to go. It has less miles and no clicks so its watiting for next spring.

Easiest way to know you have all of the right parts is to call cruiserdan and say, "I have a 199X Land Cruiser and I'm planning to do Y maintenance. Can you please box it all up and ship it to me?" There are a LOT of little bits -n- pieces involved.

A couple of spare wheel studs, nuts and cone washers is a good idea too just in case you are missing a few or have a penchance for breaking $#!&.
 
Last edited:
100 series pads? i didnt know they were interchagable. better braking i assume? does this go for both axles or just the front?
 
Last edited:
Front only!

Lots of good reading if you search. I second the "While in there" You will be using lots of time to get in, so do it all. Hard to say if the birf is bad. You may not know until you give it a good cleaning. First try swapping right to left. Maybe this will extend the life. In my case I will need to go back and replace the birf this spring.

Good Luck
 
Back
Top Bottom