Birfields 240K?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 22, 2004
Threads
80
Messages
245
Hey Guys,

I am rebuilding my old 91. It has 240K on it. In talking to the PO, I dont think the axles have ever been rebuilt. The brakes have been done but thats it. Its not leaking, no clicking, no grinding. I have bought the kit from Cdan but am wondering if it needs to be done yet. Is there any other way to check it?

The 80 was basically used as a socal commuter car. Both PO I know and both had all mx done at dealer. Both were a little anal about mx too.

Thanks!
BC
 
The preferred time to do it is before it starts clicking and grinding. If it gets that far, it needs many more dollars to fix. I'd do it.
At very least pull one side apart and check out the grease. If it looks wonderful, it's probably been done recently. It probably won't look wonderful.

-Spike
 
have you checked the front diff oil and the knuckle grease? I didn't have any clicking, grinding, or leaking, but when I changed my diff oil it was a very thick mix of moly grease and gear oil. I changed it and pumped grease into the knuckles about every 500 miles until I could find time to do the rebuild. both inner oil seals and one hub seal were toast, grease started pouring out on one side as soon as I took the drive plate off. I would do it to be safe. It isn't hard, just messy and time consuming.
 
Have you put it on jacks, placed it in nuetral, removed the dust cap and rotated the front drive shaft? If there is little to no play between the rotation of the drive shaft and the rotation of the half-shaft, I would leave it alone. Unless you just want the ease of mind and to shell out the cash. I have this problem and I'm looking for the right time to do the work. I found all the parts online (seal, shafts and bearings) for about $700. A friend of mine, a Master Toyota Tech, said it would cost about $3K in the shop.
 
240K miles? I would do the birfs and the knuckles as soon as I could.
One way to inspect the condition of the grease is to remove the grease nut (Square nut on knuckle) and insert a long stick. Look how the grease comes out. See what condition the grease is (if there's any at all). You may add more grease as a short term fix. The Knuckles use only a Moly based grease. Using any other type of grease may destroy both, turning them to a gooey oil.

If you don't hear clicking and there hasn't been any maintenance in there, you are a lucky guy. Stop tempting fate and do the service. New birfs are a lot more money than taking the knuckles apart and servicing them.

Regards

Alvaro
 
Have you put it on jacks, placed it in nuetral, removed the dust cap and rotated the front drive shaft? If there is little to no play between the rotation of the drive shaft and the rotation of the half-shaft, I would leave it alone. Unless you just want the ease of mind and to shell out the cash. I have this problem and I'm looking for the right time to do the work. I found all the parts online (seal, shafts and bearings) for about $700. A friend of mine, a Master Toyota Tech, said it would cost about $3K in the shop.

i thought you could get the parts for much less than $700? am i wrong
 
i thought you could get the parts for much less than $700? am i wrong

If you service it before you get that 'play' he mentioned, yes. If you wait for them to get loose, you have to replace the birfields. Not good advice, in my opinion. Doing the maintenence before they get trashed should cost you under $200.

-Spike
 
Have you put it on jacks, placed it in nuetral, removed the dust cap and rotated the front drive shaft? If there is little to no play between the rotation of the drive shaft and the rotation of the half-shaft, I would leave it alone. Unless you just want the ease of mind and to shell out the cash. I have this problem and I'm looking for the right time to do the work. I found all the parts online (seal, shafts and bearings) for about $700. A friend of mine, a Master Toyota Tech, said it would cost about $3K in the shop.

This method tells you absolutely nothing about the condition of seals, bearings, grease, oil, or anything else you'd want to know. Checking the play in the front axle doesn't tell you if the worn parts are the ring and pinion, various bearings, axle splines, birfields, drive hubs, or what. Waiting until you have noticeable play in a system is a good way to guarantee a large repair bill. If you keep everything lubricated and sealed properly, you should never have play in those parts. If you do, you're beyond the required maintenance and right into replacing parts that you shouldn't need to replace on a well-maintained vehicle.

-Spike
 
The original thread is "Birfields 240k?". Where does it state "seals, bearings, grease, oil, or anything else"? READ THE THREAD. The method I stated earlier is the only way to check the bir's without breaking the diff all apart. Not my method, but the method used by Toyota Techs. As for grease and seal breakdown, look at the out surface of the knuckle. If you see a combination of the diff oil and moly grease coming out, then you have seal erosion. Of course, this is only way to observe from outside the dif. As for the cost to repair both bir's, seals, and bearings, if you have another source I very interested and welcome the though of being wrong.
 
The original thread is "Birfields 240k?". Where does it state "seals, bearings, grease, oil, or anything else"? READ THE THREAD. The method I stated earlier is the only way to check the bir's without breaking the diff all apart. Not my method, but the method used by Toyota Techs. As for grease and seal breakdown, look at the out surface of the knuckle. If you see a combination of the diff oil and moly grease coming out, then you have seal erosion. Of course, this is only way to observe from outside the dif. As for the cost to repair both bir's, seals, and bearings, if you have another source I very interested and welcome the though of being wrong.

https://forum.ih8mud.com/showthread.php?t=78276

seals, bearings, grease, and oil are part of the front axle service from the faq(same in the FSM) - this is what most people on here are talking about when they talk about rebuilding the axle, repacking the birfs, etc. - about 200 in parts and grease, which I am assuming is what he has already bought from cdan. most have said @ 1000 to have it done iirc
 
The original thread is "Birfields 240k?". Where does it state "seals, bearings, grease, oil, or anything else"? READ THE THREAD.

rbpeason4,

You are new around here. Generally, when some members talk about rebuilding the front axle as mentioned by bcripe, they are thinking about what you or your mechanic friend would think of as a CV service or knuckle service or full front axle service.

On the 80 Series, it is rare that we have to "rebuild" front axles which technically would involve replacing the CV (birfield) joints and the spindles (and probably some diff bearings and gears) in conjuction with repacking the grease and replacing all the seals.

So, technically you are correct, the poster asked about rebuilding the axle, but the responses the OP got were recommendations for a front axle service; which very likely is well overdue at 240k. The OP mentions that he did not think the front axle had ever been serviced. Frankly, I don't think an 80-Series front end will last 240k without at least 1 full front axle service but I suppose it is possible.

-B-
 
OK, I did not mean a technical full rebuild. Just a complete disassembly, inspect and new seals, grease, oil, etc.

Ill go ahead and get it done.

Thanks,
BC
 
BC,

At 240K you are in for a whole knuckle job.
You are already there, might as well change the 4 bearings and the knuckle seals.

Alvaro
 
The original thread is "Birfields 240k?". Where does it state "seals, bearings, grease, oil, or anything else"? READ THE THREAD.

Begging your pardon, I thought he was talking about servicing the front axle, which he thought hadn't ever been done. The 'kit' C-Dan puts together is for an axle service, so I assumed that's what he was asking. I defer to your and your master mechanic's superior knowledge as for how to diagnose worn birfields; however I think I'll continue to inspect the birfields when I service the axle to determine when I need extra parts, and which ones. I just can't see myself making up a parts list by checking the play in the front axle components without turning a single bolt. I guess I just don't have enough experience for that. Kudos to your mechanic friend for his incredible abilities.

-Spike
 
Back
Top Bottom