BIRF time bomb?

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 13, 2007
Threads
108
Messages
479
Location
Arizona
My rig just passed 200,000 miles this week. It has also been called up to DD duty. I'll drive over 20,000 miles this year back and forth to school and work. Im worried about the BIRFs. I sometimes get the clicking noise when I turn sharp at low speeds (U-turns).

I wont been doing any trail running this year. All high way miles till I finish Paramedic school. Whats the worse that can happen? Can they just snap? What am I looking at as far cost for parts and labor?
 
If' you're not planning to drive in conditions that would need 4WD then just disconnect the front drive shaft. You won't stress the birfs. I also think that highway driving won't cause much trouble to your birfs if you drive it gently

Don't disconnect the front driveshave unless you have a "center diferential locking swith" (CDL). With the center diff unlocked and no front driveshaft, most of the drive force will go to the disconnected front flange. What little force goes to the rear wheels will do so at a different flange speed than the front eventually overheating and damaging the center diff.

If you want to go that route, Slee has the CDL switch in the $60 range. A lot cheaper than Birfs.

I think Birfs are about $300 each plus an axle maintennance kit and expendables. Maybe $900 for parts.

:cool:
 
Oh damn.. I assumed almost everyone has the center diff lock. And you don't have to buy a CDL switch from Slee. You can buy a hazard switch for $5 (ebay) as it is exactly the same switch but with a different label.

And birfs can be bought from $50 per piece. OEMs are expensive but aftermarket will do if you're not into extreme 4x4.
 
His is a FJ80, they have the switch. A switch isn't needed on any of the 80's, just lock the center, remove the diff fuse and drive.
 
Oh damn.. I assumed almost everyone has the center diff lock. And you don't have to buy a CDL switch from Slee. You can buy a hazard switch for $5 (ebay) as it is exactly the same switch but with a different label.

And birfs can be bought from $50 per piece. OEMs are expensive but aftermarket will do if you're not into extreme 4x4.

Who's got new OEM quality (or equivalent) ABS Birfs for $50.00. At that price I'll do them as preventive maintenance.

Cool tip about the hazard flasher switch.

:cool:
 
His is a FJ80, they have the switch. A switch isn't needed on any of the 80's, just lock the center, remove the diff fuse and drive.


Kevin, didn't you mean: remove (front) drive shaft, instead of "diff fuse"?
 
Who's got new OEM quality (or equivalent) ABS Birfs for $50.00. At that price I'll do them as preventive maintenance.

This is one:
CV joint Toyota Landcruiser 80 series early up to 1994 - eBay 4x4 Accessories, Exterior, Car Parts, Accessories, Cars, Bikes, Boats. (end time 22-Dec-08 08:27:36 AEDST)

In Australia all cruiser stuff is cheap, so these are 55AUD. I've just started to buy from Australia as it is cheaper than the US for cruiser parts. Well, the shipping sucks a bit but I still have a good gain margin over the US prices (not that the dollar went up a bit).
 
My rig just passed 200,000 miles this week. It has also been called up to DD duty. I'll drive over 20,000 miles this year back and forth to school and work. Im worried about the BIRFs. I sometimes get the clicking noise when I turn sharp at low speeds (U-turns).

I wont been doing any trail running this year. All high way miles till I finish Paramedic school. Whats the worse that can happen? Can they just snap? What am I looking at as far cost for parts and labor?

:whoops:out of my '93
birfields2.webp
 
So I drive it mellow I should be ok, until I can find someone to help me with the rebuild? 95% of my driving is highway right now.

Good thing gas is cheap. I sure do love driving my 80 over my RIP Focus. Im really torn up that the HG went in my Focus and now I have to drive the 80. NOT!!!!!!!!!!!!!!!!!!
 
This is one:
1
CV joint Toyota Landcruiser 80 series early up to 1994 - eBay 4x4 Accessories, Exterior, Car Parts, Accessories, Cars, Bikes, Boats. (end time 22-Dec-08 08:27:36 AEDST)

In Australia all cruiser stuff is cheap, so these are 55AUD. I've just started to buy from Australia as it is cheaper than the US for cruiser parts. Well, the shipping sucks a bit but I still have a good gain margin over the US prices (not that the dollar went up a bit).

ebay said:
The brand of this CV is Motorchamp, made in China.

Pass.
 
I have been thinking of converting to part time 4WD with Slee's kit. Does that have anything to do with the BIRFs. Would I be killing two birds with one stone?
 
That Ebay item is mislabeled. Not to rain on anyone's parade, but he's not selling the CV joint as the verbal description seems to indicate. The picture only shows the stub axle and that's only a good price not a spectacular price. The expensive part (the star, balls and clip) is missing in the picture. Ironically his text is full of warnings about your axle "clicking" and needing his part but the clicking doesn't come from his part alone so this won't fix it. He's only selling the stub axle.

DougM
 
So I drive it mellow I should be ok, until I can find someone to help me with the rebuild? 95% of my driving is highway right now.

Good thing gas is cheap. I sure do love driving my 80 over my RIP Focus. Im really torn up that the HG went in my Focus and now I have to drive the 80. NOT!!!!!!!!!!!!!!!!!!

that what happen to me on h/w 70mi+ do it now before it to late
 
The picture only shows the stub axle and that's only a good price not a spectacular price. The expensive part (the star, balls and clip) is missing in the picture.

Are you sure? I thought that birfs are called CV joints in Austraila. Otherwise it would have been an axle and not a 'joint'. I bought a birf on a local website and paid a similar price. My birfs were made in Italy. Still on the shelf and I will install them soon and report.

If anyone is interested you could ask the guy what he's selling and we will have the doubts sorted out.
 
Does anyone know if the part time 4WD conversion will also tacke my BIRF problem?
 
you problem it birf' soon or later you have too:doh:
 
Why not just get a knuckle rebuild kit and new bearings and service the front end? You'd be into it for $150 or so w/ materials, swap the birfs side-to-side, and you should be perfectly fine. If you can't do the job yourself, ask some local 'Mudders to assist (then add another $50+ for beer).
 
Mike, the picture on the Ebay link shows just the tulip bell laying there.

DougM
 
Back
Top Bottom