Bead blasted my wheels

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Sorry for posting this and then disapearing, had a router die at work.

Do I need to clear coat them? As tooth fairy mentioned the shop that did these builds performance aluminum jetski parts with no coatings. Will they discolor or what if I don't coat them. I love the flat color just as is. He charged me $15 to do one. It is a centrifigal force blaster using stainless steel shot as the media.
 
I actually had this one blasted while the tire was removed due to tread failure. He can blast them with tire mounted, but only one would fit in the cabinet at a time.
 
Sorry for posting this and then disapearing, had a router die at work.

Hijack on!
ewh. We thought our gateway router died the other week. I sat up her with the ISP tech until 1 in the morning. It turned out that our 2 bonded T1's were the problem. Found it out by mistake since our ISP was just trying to get us up on a sinlge T and a loaned router, but couldn't, then re-bonded the two T's and reconnected to our router... presto, we're baaaaaack. It was never the router in the first place and it got corrected by mistake. Gotta love those scenarios. I was pissed because it was the night Auburn played Thursday night football.

Hijack off!
 
Sorry for posting this and then disapearing, had a router die at work.

Do I need to clear coat them? As tooth fairy mentioned the shop that did these builds performance aluminum jetski parts with no coatings. Will they discolor or what if I don't coat them. I love the flat color just as is. He charged me $15 to do one. It is a centrifigal force blaster using stainless steel shot as the media.

The alloy started oxidizing the second it was removed from the blaster and will continue until coated. The blasted surface is very good at adhering dirt and hard to clean, clear coat will make maintenance easier.
 
The alloy started oxidizing the second it was removed from the blaster and will continue until coated. The blasted surface is very good at adhering dirt and hard to clean, clear coat will make maintenance easier.

Is there something good to clean with before I clear coat or do I need to take it back and have him reblast it.
 
Is there something good to clean with before I clear coat or do I need to take it back and have him reblast it.

Clean with acetone or lacquer thinner and spray.
 
So will MEK or the other cleaners remove the corrosion thats already started or do I need another steep before I rattle can with satin clear coat.
 
How severe is the corrosion? Can you get pics of it?

MEK etc is used to remove the surface contaminates, not etch or remove the metal. Depending on how severe the corrosion is, you may need to get more agressive.

How long has the corriosion been going on?

EDIT: To get a truely professional looking finish you should technically etch the wheels and use a compound like bondo to fill any imperfections, then spray them the aluminum color (shade) of your choice, and clear coat them correctly, allowing them to cure, possibly with multiple clearcoat layers. Depends on how important the look of the wheel is to you.
 
I love the satin finish. Clear coat will work, but clear powder coat will last forever.

Unless you wheel and rub them on rock!
 
What is MEK.

Methyl Ethyl Ketone iirc. You can buy it in a powder form at Ace. Just and some water and elbow grease.

I don't think you would have to reblast them. Some materials need an oxide layer to have products adhere to them , like, titanium for instance. There is a step during polishing of titanium that we have to let it "skin" before we can proceed.

Butch
 
How severe is the corrosion? How long has the corriosion been going on?

It's been a week since it was blasted, I noticed a slight discoloration from the goop the tire shop used during remounting. It might rinnse off I didn't try yet.

I only had 1 of 5 rims blasted so far, so if I need him to touch up the first one it's not a big deal.
 
corrosion on aluminium is a good thing. the aluminium oxide that forms creates a protective layer that stops further corrosion, unlike iron oxide (rust)...

esthetics is a different story. If it doesn't look good, strip it before you coat it.
 
Back
Top Bottom