And now for my brake problem

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 31, 2005
Threads
28
Messages
129
Location
puyallup wa
Drums all around with mini truck booster. i installed the booster about 1 month ago and had to adjust mc push rod all the way back and adjust brake shoes 5 cliks off of tight( like manual says) to have good pedal feel. anyway everything was working fine until today after driving around on the freeway (which i dont usually do) my brakes began to drag. i usually roll backwards in my driveway, but when i got home i didnt even have to set the e-bake to hold still. got back in her in a few hours later and pedal was back to normal, and about 5 mins after driving it brakes did the same thing again? the pressure was so tight that i could get the brakes to grab hard before brake light would even come on, and my brake light switch it adjusted to the very top. not sure what it is. i think that i am missing some sort of inline check valve for the mini truck booster, but i though that was just to help hold pressure. im lost?!?!
 
get used to it.
i've been trying to resolve this problem for 4 years. i've rebuilt every part of my brake system 3 times, and the damn thing still doesn't work.
my next move is to do a front disk conversion and see if it relieves my headache.
my front brakes were the ones always behaving as you describe, never the rear ones.
if you figure it out, please advice.
 
you need to adjust the rod in the brake booster,sounds like it is too long ... there is a sst for measuring the length of the rod ( basicly the rod is as long as the hole is deep.) they have to match.
 
well the rod in my brake booster is already adjusted all the way down, so there is no room for adjustment there, but the thing is the brakes were fine for about a month, pedal feel was good and not to high. i dont see how it it a wrong adjustment would cause this after it has been acting fine for a month. but what do i know. well if it is the booster rod, how do i shorten it?
 
When I put a 60 booster into my 40, I had to shorten the rod so much I couldn't use the lock nut (no threads left for it).
Dont assume because it's 'all the way in' that it's correct.

You get to the other rod by pulling the m/cyl out of the way (you can leave the pipes connected) - adjustment is easy - you need to shorten it a little.

You could also check the next time you get the 'grab' problem by jacking up the vehicle and seeing which wheels are grabbing - it might be a collapsed brake hose...
 
Had a similar problem when I put on a M/C from a mini. THe brakes would get tighter and tighter the more I drove.
Double checked the whole system and everything was in specs. The brakes worked prior to the M/C swap, even though you had to pump them up, so I purchased a correct TLC M/C and that was the end of the problem.
My thoughts were that the minis are front discs and putting it on a 40 without discs was the problems. Didn't get a chance to really experiment, but I would throw a guess that it has something to do with a built in residual vavle in the M/C.
 
How old are the brake hoses? One of them may have the inner lining seperating, which acts like a one way check valve, causing the downstream brake(s) to drag.

Most rear axles have one flexible hose, so usually both rear brakes hang up.

Most front wheels have one flexible hose each, so generally only one front wheel hangs up. An exception are 4x4's that have a flexible line to the axle, which then runs to a flexible line at each wheel. In this style, if both front wheels hang up, then it's probably the single line from the frame to the axle.

If it is ALL wheels hanging up, the trouble is generally in the master cylinder, the booster, or in the brake proportioning valve manifold.

The above is actually very tight brakes that start out loose and then start binding as you drive. Now, if the brakes just simply grab, especially as they get hot, and really grab, it could be a blown axle seal that is starting to dump gear oil onto the brake shoes. This makes the shoes grab the drums. You might not even see evidence of the leak, but you can feel the sympton of it when the shoe grabs. Generally, though, this happens to only one drum, unless something has caused an overpressure situation in the axle that forces lube out of both of the seals at the same time. If you had an oil change done recently at a Gypy Lube and they overfilled the axle, well, that might do it.

I am not an expert on the FJ-40. The above are general guidelines for all vehicles.
 
i know this isn't in the same vehicle class but. I had a problem like that with my brand new crf 450r the brakes would grab when they got hot. I bled it really well and solved the problem, maybe you have some air in the system!!
 
bikinnotdykin said:
i know this isn't in the same vehicle class but. I had a problem like that with my brand new crf 450r the brakes would grab when they got hot. I bled it really well and solved the problem, maybe you have some air in the system!!
that was one thing the install manual of my last master cyl said. "Brakes Catch: Air in the lines" as one of the Problem/Solution in the solution table
 
Back
Top Bottom