am I on crack

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Sep 9, 2006
Threads
10
Messages
29
Location
Albuquerque New Mexico
need help guys.

Firt and formost I have done my research, so much that I have confused the hell out of myself.

Is this setup doable or am I on crack?

1968 fj40

1 tbi 350
2 sm420 or sm465 (depends on what I can find and afford)
3 np203 to np205 doubler (best adapter to go with?)
4 hybrid rear axle ( fj diff and mini outers)
5 OME springs and hangers out of an fj55, only a few hundremiles on leafs, has shackel reversed alredy.and I think made for 2'' lift.
6 soa
7 38'' min on tires
8 detroit lockers already in both diffs.


Some opinions would be great,,,am I on the right path or what guys?

:beer: :beer: All Around!:beer: :beer:
 
Tell us what you want to do with the truck!
What you have will work for a good crawler/trail rig for sure

Nocents
 
Hell yes your on crack cause you own a Land Cuiser. #3 is a long setup for a 40. I think it would have problems with #6 combined with #5 (2" lift). I am assuming that you're going to stretch the wheel base in the rear? Doubler kits alone are almost 1/2 the price of an Orion, plus the price of the 205, 203 reduction box, and doner mini truck axle, inevetible nickle and dime items, and a lot of hours getting everything in. My 2 cents and a long story short is that after swapping to a Dana 300 and building a LC/Mini hybrid axle it would have been a lot easier to buy an Orion and throw it in.
Also, as far as the centered rear axle goes, in case you didn't see it, check out the link in the Tech section about flipping your housing end for end so that the pumpkin is on the drivers side. I haven't done any measuring on how this would turn out, but it might give you the same result, just opposite as far as the side to side driveshaft angle is concerened as compared to a LC/Mini hybrid axle. The reason I say "opposite" is because my rear shaft is running at a 2 plane angle with the hybrid because the LC pinion is offset to the passenger side of the third member. I use a stock length 60 series CV style shaft and it veers about 1.5" off the transfer case centerline, towards the passenger side, where it meets the pinion flange.:doh: HTH, have fun
 
sorry for not stating the truck will be used for rockcrawling and a trail rig only. little to no road use

length and price are my two main concerns.

I have thought about Orion but price is high and not sure if it hase gear opions im looking for

most of the coments helped, but B2BER what do you think will be the problem with doing a spring over with the OME springs off the fj55?
 
most of the coments helped, but B2BER what do you think will be the problem with doing a spring over with the OME springs off the fj55?

Most don't like to SOA with lift springs, too high. But I've known a few that had to use add-a-leafs when going SOA with stock springs.

Depending on how much the OMEs off the 55 have settled, you might end up about perfect. If not you can pull a leaf, but I'm not sure which one is best.

Someone should chime in that's done this.
 
Why is it a problem to go SOA with a lift spring?
I am not sure it is 2'', but it looks taller than stock on the fj55.
Should not have any setteling, only has a few milles and very little time under the pig.
My reserch has shown that most of you guys feel tho OME springs are a quality product, or am I missing something?:confused: :confused:
 
Sorry, the original post font was too small and my eyes are old. Didn't see the "min".

Nothing wrong with OME quality (that I know of), just stating that all springs settle over time. You could prolly get 38s under an SOA rig with stock springs, so you're on the right track going with the lift springs for possible 40"s.

I say do it, take pics and post the results and experience for the rest of us.
 
most of the coments helped, but B2BER what do you think will be the problem with doing a spring over with the OME springs off the fj55?

I was just thinking there would some drive shaft length/angle issues with that much lift and the length of a doubler. Plus when you have a centered output on your transfer there will be a disadvantage because the output shaft will be higher up in the frame rails than a stock LC case. With the doubler at about 36" long and a stock rear axle location you should end up with a 15" long driveshaft. I'm guessing you'd at least have to extend the wheelbase on the rear.
BTW, just for clarification on what I was saying about flipping the rear housing to acheive a more centered pinion, I was refering to notching the housing for the ring gear so the third member can be installed with its normal orientation. I saw this in a thread or link awhile ago but can't seem to find it anymore:confused:
 
in my opinion ,i would wait till you got the money together and build what you altimately want meaning you can spend money on doublers etc and have issues after where as buying a atlas will solve that
as far your springs fj40 springs work great they flex nice have a soft ride and soa will give you the lift you want even with longer shackles
the rear axle you will have to change and ford 9" can be had at a descent price
providing you dont jump straight into a nicely put together 35 or 40 spline inner axles and hi9 (which i think is one of the best mods for a fj)
if a nine is ,nt in your budget then mini truck axles and a spool can be had cheap but you may have to go easy on it with a v8 and 40"tires
even a 14 bolt rear can be found at a cheap price around $250 at a junk yard but you will have to cut it down and buy custom made inner axles but at least you will not have to buy another axle and can romp on it all you like
the sm420 or 465 is a reasonable inexpensive tranny and has the low 1st gears that you will need for crawling and can be adapted with used parts so you could keep your 4:10 axle ratio without haveing to change the ring gears (trail only rig) and still will not have rear drive shaft issues, good luck
thats my more than .02 cents worth
 
Ok I'm starting to second guess the idea of the doubler.... Now what? big differences between Orion and Atlas? (besides center vs. offset dif) Du. Orion seems to be alot cheeper, but gearing options do seem to be limited and not as low. Am I right?
 
I stated they are OME springs but I might be wrong. They look new and are on a fj55 I picked up. the shocks are OME so I just figured one and one was two. the shackels are on the back side on the front and rear. It also looks like the pig sits highter than stock.

the pig would make a much simpler project, it runs great has the new springs, shocks, lockers, and OME rear tire carrier bumper, but I have always wanted a 40.
 
Back
Top Bottom