Always check your hubs...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Apr 17, 2015
Threads
18
Messages
195
Location
Hillsboro, OR
So I went about a thousand mile passed my normal maintenance interval, got my truck on jack stands, and my driver side wheel was basically falling off.

So I thought to myself, must be a lose nut, this’ll be a 15 minute job...

Turns out the adjustment nut is now welded to the spindle, the lock washer is disintegrated and melted to drive flange, which is in turn welded to the lock nut.


F4D4843D-DEBD-4E06-B786-647448B6B591.jpeg
6BD2683A-37F2-44BE-B35C-15112F2E790B.jpeg
8261A15D-4EFC-49D8-98E0-506539916BBA.jpeg
 
Oof. Good thing you didn't have a catastrophic failure at speed.
 
Thanks for sharing so we can avoid the same. How many miles is the maintenance interval you mentioned?
 
Couldn't agree more. I'm pretty upset this is going to take a while to fix and wasn't budgeted for (we just had our first kid), but very pleased that it wasn't while on a trip with said child.
Glad you're safe. That was all a loose wheel bearing issue.

New spindle, bearings, seals, maybe a drive flange, maybe a hub, depending on what you see when you open it up.

When you go back together........ 35 LB-FT on the inner nut while rotating. Then start washer, then 45 LB-FT on the outer nut, then bend the tabs onto BOTH nuts.
 
Maybe change the title to "hub" instead of "knuckle" since everyone will be expecting something very different. But still a good visual for folks.
 
Glad you're safe. That was all a loose wheel bearing issue.

New spindle, bearings, seals, maybe a drive flange, maybe a hub, depending on what you see when you open it up.

When you go back together........ 35 LB-FT on the inner nut while rotating. Then start washer, then 45 LB-FT on the outer nut, then bend the tabs onto BOTH nuts.

Yep, rebuilt the whole thing 30k ago, and check it every 4-5k miles. Haven’t ever had cause to dig in deeper, the wheel hasn’t been “loose” until this last one.

Oh well, parts aren’t that bad, and the process is a lot easier now that’s I’ve done it multiple times.
 
What do you torque your wheel bearings to? Also was it pulling to that side when driving? From my experience on a similar issue it was.
 
What do you torque your wheel bearings to? Also was it pulling to that side when driving? From my experience on a similar issue it was.

Torqued adjustment nut to whatever makes the wheel stable, then lock nut to 46 pounds or whatever it says on the sheet. I probably messed with it too much when I did my last tire rotation, and it just took a bunch of miles to really work loose.

Wasn’t pulling harder than it normally does (suspension is shot), though I do remember a sudden pull about a week ago (but couldn’t replicate), that’s probably when the washer dynamited. Also didn’t observe any noise or smell.
 
Something similar happened to me. I started to hear a front end squeak and decided to check my new bearings. Turns out that I welded by bearing rollers together. That was fun... yah the manual says inch pounds not foot pounds. Better off just doing it by feel and not with a torque wrench is my experience.
 
Something similar happened to me. I started to hear a front end squeak and decided to check my new bearings. Turns out that I welded by bearing rollers together. That was fun... yah the manual says inch pounds not foot pounds. Better off just doing it by feel and not with a torque wrench is my experience.

Hmm... no it doesn't:

Check that the bearing has no play.
(f) Using a spring tension gauge, measure the preload.
Preload (at starting):
28 - 56 N (2.9 - 5.7 kgf, 6.4 - 12.6 lbf)
6. INSTALL LOCK WASHER AND LOCK NUT
(a) Install a new lock washer and lock nut.
(b) Using SST, torque the lock nut.
SST 09607-60020
Torque: 64 N·m (650 kgf·cm, 47 ft·lbf)
(c) Check that axle hub turns smoothly and that the bearing
has no play.
(d) Using a spring tension gauge, check the preload.
Preload (at starting):
28-56 N (2.9-5.7 kgf, 6.4-12.6 lbf)
If it is not within the specification, adjust it with the adjusting nut
after removing the lock washer and lock nut
 
The FSM method is far too little preload IMHO. The below has never failed me.

1) torque inner nut to 50 ft lbs to ensure that everything is seated. Turn hub back and forth a couple of times

2) loosen and retorque inner to 30 ft lbs. Rotate hub both directions repeatedly and check torque a couple of times until it doesn't change with rotation

3) insert lock washer and torque outer to spec.

4) bend tabs over both nuts from lock washer

5) drive
 
Last edited:
Back
Top Bottom