air conditioner noise

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 28, 2006
Threads
31
Messages
164
Location
in my house
I got a 97 fzj 80. The belt or pulley has always had a little sqeel when the a/c is on. nothing bad it blows super cold so I dont mind. Today however the noise got real bad. Like a bearing locking up and the sound of a belt slipping. I turned it off and right back on and it was back to the normal low squeel. Is it time for a new ac unit?
 
Funny mine started squealing today as well. I looked under the hood to investigate to find while the A/C was on the belt over the A/C pulley(clutch?) was barely turning and not turning smoothly.

It was slowly turning 1/4 then quickly jump 1/4 then slowly turn. Is this the A/C clutch? The result in the cab is the A/C begins to blow cold but then when the pulley is "bogged" down the air is no longer cold.

Any suggestions on how many banana job the A/C pulley / clutch is? I have recently (8/06) replaced the belts with OEM from Dan.

Thanks!
 
Loosen the belt and make sure you can turn a) the clutch pulley, and b) the compressor shaft, easily by hand. If so, the belt might have just been too loose to begin with. If not, we go from there...

Curtis
 
Any suggestions on how many banana job the A/C pulley / clutch is? Thanks!


You need a special puller for removing the clutch. Checker auto has them for loan where I live. It's so easy a caveman could do it. (with the proper tools)

Dave
 
Loosen the belt and make sure you can turn a) the clutch pulley, and b) the compressor shaft, easily by hand. If so, the belt might have just been too loose to begin with. If not, we go from there...

Curtis


So the initial test is loosen the belt and manually turn the clutch pulley and compressor shaft. Is the compressor shaft right there all in one with the pulley/clutch?

I will look in my FSM tonight as I am still at the store right now.

Thanks for the help CJF!!
 
So the initial test is loosen the belt and manually turn the clutch pulley and compressor shaft. Is the compressor shaft right there all in one with the pulley/clutch?

Clutch/pulley has the compressor shaft as its axis.

Offhand, I think the following quick test of the compressor shaft will work (I'll check for sure a little later when I get a chance.): With the engine off and without even loosening the belt, you should be able to rotate the shaft by hand, as long as there's a way to get hold of it (from in front of the clutch/pulley). Otherwise I'd think something's seizing up...

Curtis
 
Thanks Curtis! I went out and checked it. With the engine off, I was able to turn the pulley/clutch by hand fairly easily. Hopefully this is good news right? Is it possible I just don't have that belt tight enough?


I have been reading through the old threads about this same problem and you have all the answers! I appreciate your help with my diagnosis.
 
Thanks Curtis! I went out and checked it. With the engine off, I was able to turn the pulley/clutch by hand fairly easily. Hopefully this is good news right? Is it possible I just don't have that belt tight enough?

Let's go over this:

You grabbed the outermost disc of the clutch assembly and it rotated easily? Meanwhile the pulley part of of the assembly and the belt itself remained stationary? If that's the case, and there was also no play in the shaft, then yeah, I'd say the compressor seems ok.

Looking back over your first post, though, where do you think the belt was slipping?? At the crankshaft pulley? Or was it slipping over the clutch pulley? I guess try tightening the belt to spec. and give it a test run, but if it squeals again, turn it off quick, and you'll have to pull the belt off and really see what's up.


I have been reading through the old threads about this same problem and you have all the answers!

:o

I just have too much time on my hands...

Cheers,

Curtis
 
OK update...
I went out this morning and started working on it. First thing I noticed after following the troubleshoot guide in the FSM was that my belt was WAY too loose.

I removed the "debris shield" from underneath, and first thing was I found a 12mm bolt loose sitting on top of the shield. I still cannot figure out where this bolt is from.

So then I started to try to tighten the belt via the belt tensioner only to find that the tensioner was fully extended and the belt was still way loose. So I them remembered the lock bolt on the tensioner so I loosened it, loosened the tensioner and removed the belt.

The tensioner is FROZEN! Should it move freely by hand? I can't even budge it. So I am thinking I have a blown bearing in the tensioner?

Anyone else care to second my diagnosis? Thanks for all the help!

I can't find in the FSM about pulling the tensioner but I finally noticed there is a snap ring under the lock bolt. I am assuming this takes it off?
 
Huh?

Pretty sure all you need is some good snap-ring pliers.

:confused:

It looks like a triangle with a handle to hold the clutch in place so you can seperate the pressure plate then remove the snap ring. Maybe it's different on my 93 since it is R 12.

The manual calls it SST 07112-76060 but it looks like mine.
 
Curtis,

So does it sound like my tension is shot?? Guess I will be calling Dan on Monday!
 
Curtis,

So does it sound like my tension is shot?? Guess I will be calling Dan on Monday!

I'm surprised no one else has chimed in. :confused:

I have a 91 with the 3FE, so our layouts aren't the same. But if you've found a pulley/tensioner with a seized bearing, then I'd certainly think you've nailed it.

Keep us posted,

Curtis
 
I got my box-o-parts from yesterday when I got home and took 20 mins to install the new tensioner and the air filter I ordered.

This seems to have solved my problems!! Nice cold air blowing.

With out one of the fancy tools to measure the deflection of the belt, how can you make sure it is tight enough?

Thanks everyone, especially Curtis!
 
With out one of the fancy tools to measure the deflection of the belt, how can you make sure it is tight enough?

People that know what they're doing can go by feel, the rest of us have to use a gauge. Unfortunately a good gauge is about $150. The main objective is to get it tight enough so the belt doesn't slip, but not to tight to overstress the compressor.

:beer:
Rookie
 
Back
Top Bottom