add a leafs

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 6, 2003
Threads
43
Messages
133
I'm thinking about putting adda leafs on my 40. I'm not trying to increase performance or anything like that. Bottom line, I'm broke, and my new tires I bought last year rub in the rear when I go around sharp corners. I don't want to trash my tires, and my tub is already bowed out a bit from the rubbing.

I wasn't worried about it because I wasn't driving it all that much, but I'm selling my daily driver and the cruiser will take it's place. So I need to do something about the rubbage.

Eventually I'll be going SOA. But for now I just need to stop the rubbing. For as cheap as they are, add a leafs seem to be a good temporary fix. I may talk myself into a skyjacker kit though...:)

What's it take to install add a leafs? Can you do all four? It sounds like I should definetly go with the longer ones from man-a-fre because they are the better of the sh!tty rides, eh?

Mike
 
If you can, go with a complete suspension lift kit, 2.5" or 4". Add-a-leafs aren't that bad to install, remove your leaf packs, securely clamp them, remove the spring center bolt, install the add-a-leaf, install new spring center bolt(usually included with add- a-leaf kit), throw everything back in place and there you are. Add-a-leafs will give you a stiff ride, but should be an easy fix for you.
 
So,


You are 'thinking' about new springs....


You are also 'thinking' about spring over.....


Guess I would not waste my money, and more importantly, TIME on AAL's.



But that is just me.


Good luck!


-Steve
 
nuc- I had considered getting fender flares and trimming the fender wells, but how much do you actually trim away with those?

Gus- thanks for the info.

Poser- you told me everything you wouldn't do, what would you suggest as an alternative?

Thanks for your input guys

Mike
 
If you are going through the effort to remove the leaf springs, it does not make a lot of

sense to me, to put a band-aid on something that would benefit far more from new

springs. Odds on, you have stock springs in your truck. That would make them almost 30

years old. You could install the lift springs now, save the old springs, and in a year or

two, when you want to do your spring over, remove the lift springs, and sell them to

someone, as there are always people looking for them. You could just do what Iggie

suggested too, and break out the saw. There are many other options and opinions

on this out here, and I am sure that you will get more.


In any case, I hope that the double spacing has made

things more klear. ;) Time and money may be something you have far more of than others.

If that is the case, then get after the add a leaves, and let us know how much better it

rides when you are done. :rolleyes:


Good luck!


-Steve


:)
 
Hellwig helper springs, the load-leveling kind. The kit picked the @$$ end up a good 4" at least due to sagging springs. They were like 30 bucks or 50, and took 2 hours to install, mostly because I kept messing something up and having to redo something... So, 50 bucks max and 2 hours, and you're good to go. Cheap, quick, and effective, what more could you want?
 
Add a leaves if done right (few are) can result in a good ride. Formula: LONG, full length , thin added leaves. Not short, thick bricks. If done with a re arch, and heat treat afterwards, can net about 2 inches lift. Also consider a longer shackle, one inch over stock in F and 2 inches over in R. The CHEAPEST lift that might work for you is just to put 2 inch longer shackles in R; you get one inch of lift which may be enough to prevent rubbing. You are prolly not rubbing at the lip that everyone wants you to trim unless you are running 12.50 wides; more likely in the inner well. Try a R shackle lift first; then if needed add a leafs or Hellwigs. Keep it on a budget, non greasable and simple with new poly bushings. CCOT has some good ones. Shorter in front due to steering issues; stick to 1 inch over shock. The rear is prolly saggin more anyways.
 
Just added additional stock leaves in my SOA 40 - worked great, may be some loss of flex but ride quality is still about the same, little less lean on corners but no real loss of articulation.

Ed (degnol) may have some more leaves (leafs?) left in his scrap pile - he sent me his old ones for just shipping costs. The only price was time and a new center bolt and some wire wheel and spray paint dress-up.

Why not just ditch the hardtop - that should lessen the need for heavier springs :D
 
skiakhokie said:
nuc- I had considered getting fender flares and trimming the fender wells, but how much do you actually trim away with those?
depends on the flares...i'd cut away as little as you need to now, then, when you go soa or lift spring, or get the flares, cut the rest.
 
if you do an add a-leaf, wouldnt that lower your rig?? since youre spring under, and extra leaves will push the axle up higher above the spring? I would make longer shackles from 1.5" x 1/4" or thicker plate. Maybe make a 6" shackle or something, and if you need to, put in shims (steel ones) to get your pinion pointed in the right direction again.
 
dustin said:
if you do an add a-leaf, wouldnt that lower your rig?? since youre spring under, and extra leaves will push the axle up higher above the spring? I would make longer shackles from 1.5" x 1/4" or thicker plate. Maybe make a 6" shackle or something, and if you need to, put in shims (steel ones) to get your pinion pointed in the right direction again.

Add a leaf's are like 1/4" thick, raising the axle up that much is more than compensated by the resulting loss of sag in the spring pack that is letting the rig down to begin with. The extra leaf keeps more arch = higher ride height than a flat spring pack ;)

Your shackle idea leads to more problems than it solves IMO, shackle lifts are not solutions - just band-aids
 
Back
Top Bottom