97 LC Tranny Flush

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 26, 2007
Threads
9
Messages
392
Location
Southwest WA
First I'd like to say that this forum is amazing. I've had a 97 LC for a couple of years, but only discovered this forum a few weeks ago.

I read up on the FAQ forum about flushing the tranny using the tranny cooler outlet. My question is: Why not use the other end of the tranny cooler return line (and cap the inlet it connects to)? I don't know whether this line dumps back into the tranny or the drain pan, but wouldn't it then flush the out the cooler return line and more completely flush the fluid?

Maybe the difference is insignificant or the other end of the cooler return line is inaccessible. Just a thought.

Dorian
 
Doing it at the cooler (as outlined it other threads) flushes the entire system including the cooler. There is no reason to use a less accessible port. Yes, you could bypass the cooler altogether but don't you want to replace the fluid in there also?
 
I didn't mean to bypass the cooler. I meant to connect after cooler just before where the cooled fluid dumps back in (tranny/drain pan); at the end of the cooler return line instead of the cooler outlet. The difference is probably negligible.
 
I'm not sure I ever saw a conclusive statement on how the fluid actually flows and if the hose you disconnect at the tranny cooler is the outflow or the inflow?

If it is indeed the "inflow" you wouldn't be flushing what is in the cooler and return line but if it the outflow from the cooler then all you miss is flushing the return line

I guess for me I didn't give it a second thought and after going through 20 qts on a full flush I can't imagine the little that you may not have flushed in the return line is going to matter. :)

The hardest part of the whole process is pumping and filling...You can't fill near as fast as the tranny can pump out so it helps to have someone that can start the rig, run through the gears, and shut it back down while you keep an eye on the amount of fluid coming out and amount you are putting in.

The only thing I would do differently if I ever had to do this again is to mark the at graduated 4 qt levels.
 
Last edited:
corsair23,

I'm talking about the cooler outflow and associated cooler return line.

Yeah, I figured it was splitting hairs.

I've also read and thought about how fast fluid will pump out. Like you suggested, I'm going to graduated the waste fluid buckets.

Cheers!
 
corsair23,

I'm talking about the cooler outflow and associated cooler return line.

Yeah, I figured it was splitting hairs.

I've also read and thought about how fast fluid will pump out. Like you suggested, I'm going to graduated the waste fluid buckets.

Cheers!

Yeah, I just couldn't recall if it was definitively concluded that the hose you disconnect truly is the outflow from the cooler or not.

Let us know how it goes. I'm only a 1 :banana: kind of guy and found it took longer to set everything up (get off the grill, etc.) than it did to do the flush itself. As for the flow, let's just say if someone ever loses a cooler line the tranny will be empty of fluid is very short order :eek:
 
I did this process yesterday breathed. Your right, you should take the return line hose off of the top of the cooler and drain through it. I didn't realize that the top was the return and the bottom was from the tranny when i did it. Now I know.

If your spending the time and money to do this process, then you should do it right.

The fluid exchange did make a difference in my hard shifts that I was having. I still get them here and there, but I just got the 80 & I'm still base lining it.

If you have not drained your transfer case recently, I would suggest doing it as well.
 
Yeah, I'm planning on getting a few quarts of 75W-90 tomorrow when I pick up a few gallons of ATF and a couple of buckets. Hopefully I'll get both done tomorrow.
 
Well, I did the tranny flush and changed the transfer case oil. The flush itself was easy as pie. The hard part was getting the return hose off of the a/t cooler outlet. I spent more time removing the cooler and wiggling the hose off. After that it was a cake walk. I'd pump out 3-4 quarts and add it back in. I used these buckets I got from home depot that are translucent white and have 1 quart graduations. I put about 19 quarts or so through. I think I'm running about a quart low right now, but haven't had a chance to get the tranny up to temp yet to get an accurate reading. I didn't think it would make much difference in how the car shifted as it was pretty smooth for it's age, but it actually did smooth out quite a bit.

I also changed the gear oil in the transfer case. I don't know when/if it's been done. The oil wasn't too bad so it's probably been done before. I did manage to break all three bolts off that hold the skid plate on. Each one came out about halfway (I imagine from how much stud is left on the head) and then twisted off flush.

I don't think an e-z out will work with the studs that are still frozen in. I suppose I'll have to drill and grind out each one. Hopefully I can keep from buggering up the female threads. Any suggestions?
 
Ok - but did you drop the pan and clean the filter. That ain't easy as pie....
 
No, I didn't. Just a fluid exchange. Maybe I'll drop the pan in the spring. I'm sure the filter and magnets could use a cleaning.
 
Whatever you wear that day plan on throwing it all away. Tranny fluid is some nasty stuff. And a partial change is better than none any day - good on you...just checking...the whole banana is a PITA.
 
Spartan, I didn't just drain the pan and refill. I drain the pan, refilled plus one quart, extended the a/t cooler outlet and pumped 19 quarts of new atf through. I purposely avoided dropping the pan. I've done it on other cars. It is a PITA.
 
I avoided it for years as well. When I did pull it - nothing incredible, but it was worth doing, the filter had gunk in it, unlike the " Prestone Kit " flush thing i just did which was a waste of time and effort.
 
Spartan, I didn't just drain the pan and refill. I drain the pan, refilled plus one quart, extended the a/t cooler outlet and pumped 19 quarts of new atf through. I purposely avoided dropping the pan. I've done it on other cars. It is a PITA.

The last pan I dropped left a bad taste in my mouth. I was seeing RED for weeks.

It is a PITA but it's a rite of passage so probably next weekend.

:beer:
 
Back
Top Bottom