97 1fzfe no start

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Dec 19, 2019
Threads
1
Messages
6
Location
Oklahoma city
Just rebuilt the engine, put it back in, getting no injector pulse but do have very strong spark.
Swap distributors, I now get injectors for about 1 second, but no spark at all.
Swap another distributor in, I now get pulse for about 1 second, and intermittent spark ever few revolutions.
If I swap the original distributor back in, I have strong spark again, but absolutely no injector pulse.

These are aftermarket spectra distributors. Dealer wants 900 for a new one, so I'm trying aftermarket first. I've heard aftermarket distributors are notoriously bad for these, but can I really get 2 bad ones in a row? Is there something else I should be checking? Literally everything else works, all fuses good, all grounds cleaned, etc.... And seeing as to how I have spark and injectors intermittently makes me think it could only be something with the distributor.
 
Spectra distributor s are s***.

I went through 5 of them on a SBC and finally decided to spend the big dollars for a brand name.

Get a used one from someone here
@slow95z
@arcteryx

Are you REALLY sure the problem is the distributor to begin with?
 
Spectra distributor s are s***.

I went through 5 of them on a SBC and finally decided to spend the big dollars for a brand name.

Get a used one from someone here
@slow95z
@arcteryx

Are you REALLY sure the problem is the distributor to begin with?


95% Sure. I have spark with the old one, but no injector pulse. With the new ones I'm getting injector pulse, but no spark (or very intermittent spark, with a weak attempt to fire)
 
Going back to the beginning, with engine not running, and key in RUN position, is the CEL on?
 
Yes it is. Fuel pump doesn't prime until you start cranking though. Always thought that was a little odd.
If you're having sometimes when things work and some when not, it's possible that you have a fusible link that is a bit "iffy" and providing contact sometimes, and sometimes not.

It may be worthwhile to put in your original distributor and change the fusible links. For $18 it's worthwhile, especially if they are of unknown origin.

Also , with injectors being an issue, I would look at the main harness by the EGR to see if any of the wires are cracked, burnt, shorts. The switch is on the ground side on Toyota, so if there is an issue, they can provide odd firing issues.
 
If you're having sometimes when things work and some when not, it's possible that you have a fusible link that is a bit "iffy" and providing contact sometimes, and sometimes not.

It may be worthwhile to put in your original distributor and change the fusible links. For $18 it's worthwhile, especially if they are of unknown origin.

Also , with injectors being an issue, I would look at the main harness by the EGR to see if any of the wires are cracked, burnt, shorts. The switch is on the ground side on Toyota, so if there is an issue, they can provide odd firing issues.

Harness is intact. Actually the harness behind behind the EGR is probably the best section of it lol. The original distributor just doesn't work at all. It provides spark, but no signal to the ecu.
 
If you're getting spark from the distributor, then it's getting through the ECU. The ECU tells it to give spark or not. The injector firing comes from the ECU, not the distributor.
 
If you're getting spark from the distributor, then it's getting through the ECU. The ECU tells it to give spark or not. The injector firing comes from the ECU, not the distributor.

From what I understand, the ecu gets the cam/crank position from the distributor to determine injector timing. For spark, the distributor seems to act just like any other, with a cap and rotor and a coil with 12 volts. Is that wrong?
 
I would check the timing and the crank sensor

Timing is checked every time I install a junk distributor, unless you mean crank/cam timing. That also hasn't changed since I put the cover on.

For the crank sensor, I can read rpm with a scan tool, but I don't really understand what the crank sensor actually does in this truck since the earlier models didn't even have one.
 
Back
Top Bottom