92' Klunking????

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 4, 2008
Threads
28
Messages
217
Location
SOCAL
Every time I give a little gas or let off the gas lightly, there is a klunk:crybaby:, it sounds like it my be coming from the rear. The u-joints are good. There is a little play in the drive shaft, is this normal. :hhmm:

This is my first 80 it's a 92, I know don't say it, I should have got an 95 or newer, but I figure I'll cut my teeth on this one first.

Thanks for all the help.
 
You don't need no stinkin' '95 or newer!! : ). This is normal in the '91-'92's. I have yet to hear of one that doesn't do this to some extent. Search "Driveling Clunk," or just "Clunk" and you will find plenty of info. It is simply all the slack being taken up when you let on and off. Even with everything in good shape, after all these years, there is some slack. Drive flange, birf, differentials, ujoint, driveshaft slip yoke, t-case, etc.... All of those have a bit of slack. Mine is helped alot by greasing the zerks on the ujoints and driveshafts. There is one on each u joint, and one on each driveshaft. I usually grease each one on every oil change. Search around and you will find lots of info. Good luck, and don't give up on the '92. You chose wisely. : ).
 
Like PookieBear said, it's totally normal. It's actually from the front end....mine does it too.
 
I usually lock the CDL while driving on long straight roads with many traffic lights. Completely eliminates the clunk.

Just don't make any sharp turns with the CDL engaged.
 
Define "klunk" a relatively minor clunk/thump is normal, if more than that I would want to know where it's coming from and evaluate if it's something that needs attention. Will it make the noise if shifted R to D? If so have a helper shift while you walk around the rig and find where it's coming from.
 
there is a klunk:crybaby:,

Is it a clunk? Or a Clunk :crybaby: Or a CLUNK! Or a Clunk!!!

A clunk is normal. The others need to be checked out.

-B-
 
Sorry it took me soo long to respond, internet went down. How do we live without this stuff?
Anyway, my KLUNK turned into a klunk after I greased the driveshafts and u-joints alot. I don't think there was any grease in there at all. Now its just a thud. I'm ok with a thud verses a KLUNK.
Thanks everyone for your help.
 
Now I just need to solve my overheating problem, I have a new radiator,new water pump,new thermostat, new temp sender. It dosent overheat all the time. Only when I'm putting heavy load on it. ie: going up into the mountains with five passengers, or jumpin off the line at stops (is that even possible?), or running A/C alot. Otherwise it runs cool most of the time. What concerns me though is that its not HOT outside yet.
 
Now I just need to solve my overheating problem, I have a new radiator,new water pump,new thermostat, new temp sender. It dosent overheat all the time. Only when I'm putting heavy load on it. ie: going up into the mountains with five passengers, or jumpin off the line at stops (is that even possible?), or running A/C alot. Otherwise it runs cool most of the time. What concerns me though is that its not HOT outside yet.

Did you read how not to over grease the driveshafts?

My clunk got better with new lift. I don't know exactly why but it did.
 
Now I just need to solve my overheating problem, I have a new radiator,new water pump,new thermostat, new temp sender. It dosent overheat all the time. Only when I'm putting heavy load on it. ie: going up into the mountains with five passengers, or jumpin off the line at stops (is that even possible?), or running A/C alot. Otherwise it runs cool most of the time. What concerns me though is that its not HOT outside yet.
You need to find out is IT really over heating or is it the gauge?
 
See... no need to move to a newer one. Easier to resolve, or at least get used to, than headgasket problems anyway. : )>

Now I just need to solve my overheating problem,

Probably just a blown headgasket. Those old 3FE engines are getting long in the tooth now. :D

-B-
 
I would check out that overheating problem asap. My overheating problem turned out to be a bad headgasket and cracked head even with the 3fe. No doubt from years of overlooking the problem. Worst case is still not that bad with a 3fe though. No overhead cams or anything.
 
Back
Top Bottom