‘78 under dash light ez question

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 27, 2003
Threads
71
Messages
380
Location
North Georgia, USA
I can’t find answer in any search.

problem: I pulled my dash off on the 78 and noticed the light under the dash was disconnected. However I can’t find the wires to re-connect. (The PO put in New aftermarket light pull knob)

question: what can I wire to / tap into to get the under dash light working again?

thanks all
 
Should be a red with black stripe for power. White with black for ground. Do you have the under dash, above the heater light?
 
The light is in the dash pad
Po cut the power wires so I don’t know what to connect the light to for power

I’m assuming I connect to the headlight pull switch but not sure what wires on the switch to tap into

here is a pic of the dash light

6E768A4B-D3F2-4297-AF16-FAEFA42309E3.webp
 
On that model there would also be a light under metal dash, just above the heater controls lever.
Both use the red/black wire which is also what would come from the stock headlight switch.
Do you have the stock wiring harness?
If you have the heater control light you could tap into those wires.
 
The po removed the heater light
So that is a literally a dead end 😂

I need an alternative place to tap into
 
The po removed the heater light
So that is a literally a dead end 😂

I need an alternative place to tap into


Eazy Peezy .........


- Remove carefully your cluster meter

- again before pull off the pos. battery cable step #1

-
carefully wiggle off the black round barrel connector , and if need be the 2 white ring terminals wires , note there locations with tape or a sharpie pen ....

- locate the red wire ,/ w black tracer stripe , this is your interior illumination circut as noted above by my good mud buddy @Shark56 ...

- try to go back from the cluster black barrel as far as you can , its ok to peal a tad bit of tape off to acive this but you must
renew any removed or mising tape after you preform the below few steps

- DO not sever or cut the red wire black tracer , simply shave a 12mm long section of the red jacket off the copper strand wire

- use a red wire for sure , or a red wire black tracer stripe in perfect world 16 guage is best , 18 guage is smallest size you can go safly

- twist your new red lead on the old red wire on cluster plug , apply tad bit of flus and carefully solder it , apply some sticky both side harness thick tape then , final off black colr electrical tape , make sure u have a nice section of long 5' red wire

- run along main harness zip tie off every few inches

- run to hole in dash , and pull through add a few inches , then cut and apply bullet connector female housing and sheath

- repeat for white wire black tracer stripe

- if you do not have the correct colors and thickness guage wire and bullet style connectors , ?

please send me a PM , i can fix you up with only the best TOP shelf oem Toyota Yazaki electrical parts on the market today


- there would be no cost involved , just some MUD-SHIP on a rainy Tuesday , here at the Rising Sun mechanical SKUNK WORKS lab outside
DC .......... :)

here is what you will need , let me know if i can help in any way .......including shipping out some professionals samples today ...:D



Here we go

new service spec . Connectors and a limitless
Length of OEM color code tracer stripe wire 16guage tough as nails !


F1517522-8A01-4101-BB94-2701553520D0.webp
45816A22-5AE8-4BF9-8E58-87ED02E64371.webp
 
Last edited:
I saw what I'm guessing was your post on FB. From the pics on there, I'm guessing you probably do not have the stock wiring harness?
Do any of the gauge lights work?
If so, the wire for one of those would be what you need for the dash light.
An LED bulb would be a nice upgrade.
 
Never mind. I read the FB post. You say none of the gauges light up. Post up a pic of the dash, head light switch and the wiring if possible. I bet you have an after market wiring harness. Painless brand being the most common.
 
Ok thanks I’ll check and let you know

Feels like this should be a simple tap into but just finding the correct wires is the trick
 
Back
Top Bottom