3FE valve adjustment Issues

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Aug 26, 2008
Threads
30
Messages
215
I pulled the valve cover off for what I assume may have been the first time in the life of the truck and did all the gaps to factory specs. I could not for the life of me find the timing window so I pulled the number one spark plug and watched for the piston to reach TDC. Can anyone find a picture for me to reference the timing window.

All the valves were more tight than spec, opposite of what I thought it would be.

I got the truck back together however now there is more valve noise than ever before, like a giant sewing machine. Is this normal for a 3FE? Or did I do the valves wrong?
 
I have about 295k and have never done a valve job. I have been thinking about it though. There are pictures of the timing port here somewhere, but i don't think they will help you. Its way in the back, almost touching the firewall, and to shoot it with a timing gun you have to push some stuff aside. Yours may actually have the rubber plug in it still, keep looking down low and way back and youl find it

Mine sounds more like a typing machine
 
Your valve train is noisier because the valve stems where they meet the rocker arms are not flat anymore, so when you put a flat feeler gauge between them your adjustment is actually the feeler gauge PLUS whatever the wear is. With solid lifters a little noise is OK. That noise is telling you the valve is seating in the head and is able to be cooled by its brief contact with it. No noise could mean that the valve is not completely seating and it will overheat and burn, costing you lots of $$$.


You can probably quiet them down with a little fine tuning. Here's a link that might be helpful.

Crane Cams
 
The timing window is hard to find, I lay the right side of my head on the front part of the air canister and look direct back at the firewall. The timing window is covered by a rubber cover that will probably be caked in crud if you haven't adjusted the timing before. It will probably be easier to reach back there and pull out the cover before trying to look for it, the cover is almost impossible to see, the open window is easier. you adjusted them hot, correct?
 
Last edited:
Once you locate and open up the cover then you'll find the next issue
you'll need to deal with: it's incredibly hard to see the TDC and
timing marks on the 3FE flywheel, especially if you are working in
sunlight when setting the timing. The best approach I found is to
remove the inspection plate on the *bottom* of the bell housing and
then (with the engine off, of course) rotate the flywheel by hand until
you find the double o's next to each other. These marks are for top
dead center (TDC). Take a tiny paint brush and carefully paint white
paint inside the o's. A few flywheel teeth clockwise from the double
o's you'll find a larger single O. This is the 7* before TDC timing
mark. Put some white paint inside this O too. Then you can reinstall
the inspection plate and do the rest of your work from the engine
compartment.

For valves, you want to line up the pointer that's inside the
inspection hole just above the starter with the double o's (TDC) and
for timing you are trying to line up the pointer with the 7* mark (large O)
on the flywheel. Both will now be much easier to see because of the white
paint. This holds especially true when setting the timing b/c the
paint reflects the strobe from the timing light.
 
So I need not worrie about the valves being more loud than before? I am worried that I have not adjusted them properly.
 
I haven’t found my timing window yet either.

Here’s how I adjust my valves:

1. warm up the truck.
2. remove the valve cover
3. hook up a remote starter (usually I just use a set of jumper cables).
4. disconnect and ground the coil to dist cap wire.
5. Adjust valves- If valve is open, use the remote starter to turn the engine to unload the pushrod
:beer:
 
Back
Top Bottom