2F from pallet to engine stand....???

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jan 22, 2003
Threads
284
Messages
8,118
Location
Kansastitty
I need to move a 2F with bellhousing and clutch assembly from a pallet to an engine stand. Everything is ready to go except I need to know what is involved with removing the bellhousing and clutch.
Does the flywheel need to be removed before the bellhousing? Now don't laugh at the question because there were some six-cylinder Chebby's that needed exactly that.
I'm hoping that I can just lift the whole thing, unbolt the bellhousing and then get to the clutch/PP/flywheel.
The engine stand is mine, but I need to borrow the hoist and I just don't want to tie up the guy's hoist any longer than needed.
Can somebody run me through this?

Thanks,
Ed
 
Yes. You need to reach through the inspection hole on the bottom and remove the p-plate, then go through the trans hole and remove the flywheel. There are bolts behind the flywheel that hold the bellhousing on.

It is one serious PIA when the engine is locked up. Stupid ass design.
 
Thanks for the quick replies! Now I know what Saturday holds in store.
'Preciate it.

Ed
 
I guess it is a good thing I see these reply's I am more a toy truck guy and was going to laugh at the questions, b

ut you guys are saying that you actually have to go through and take the flywheel and pressure plate off before you can take the bellhousing off. ???? :confused:

Cant just unbolt the bellhousing and go from there. That IS a stupid design.
Good thing Toyota changed it.

Good to know now though, I would have been dumbfounded if ever trying to do it. :D
 
Jamison Workshop said:
ut you guys are saying that you actually have to go through and take the flywheel and pressure plate off before you can take the bellhousing off. ???? :confused:

Cant just unbolt the bellhousing and go from there. That IS a stupid design.
Good thing Toyota changed it.

Good to know now though, I would have been dumbfounded if ever trying to do it. :D

Yes, that is the F/2F design. Fortunately it's not the 3B design that I have so I guess the F/2F is a Chevy copy!
 
The valve keepers are interchangeable, and maybe the head bolts.

have to go through and take the flywheel and pressure plate off before you can take the bellhousing off
Remember this quirk if you ever need to change a clutch in a Kubota tractor. You have to take the tractor in half and there are two bolts inside the bellhousing that you'd never think to look for had you not first been introduced to Japanese oddities in a way like this.

(nice useless OT factoid, eh?)
 
Also, not sure what engine stand you have, but if you have one of those "T" style 750 pound jobs, then forget it. You will fold that thing in half.

You need at least a 1250 pound "U" style engine stand. That is the only thing that can stand the weight of a LONG, HEAVY 2F. Even on the 1250 stand, front of the engine sags. (today's engine stands are developed for shorter chubby V8's, not long heavy things).

Also, what has been said bout clutch removal and such is all correct. Hoist it up, remove this stuff and then push your engine stand in behind it, lower/lift the engine into place, and then bolt onto the stand and then off you go. Also keep in mind when rotating the engine on the stand to be carefull, espeically with the head still on.

Just be careful, 800 pounds of steel will kill a concrete floor, and worse your foot/feet or you!

HTH,

Dallas
 
Gumby said:
Actually, what I do is bolt the head of the engine stand to the engine first, then pick it up and slide the head onto the stand. It's way easier than lining up the arms when the engine is swinging.


Now THAT'S an idea!!! Will use!


I had a '51 Chevy Fleetline 2 door. Looked like a giant black cockroach. Not only did it have the same bellhousing design, but a "torque tube" driveshaft.
You had to pull the engine to replace the clutch.
My first car.


OK, thanks to all. Let this thing go to sleep now.




Ed
 
dmaddox said:
You need at least a 1250 pound "U" style engine stand.



HTH,

Dallas


Yeah, I bought the "U" shaped 1250lb stand. Wouldn't have known to do that except for what I read here.


I actually like my toes and my floor.



Thanks,
Ed
 
Back
Top Bottom