283 pic

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 26, 2006
Threads
111
Messages
293
Location
Longview, Texas
Here is a pic of the 283 in a 74/40. Osagecruiser was asking.... This rig was also used for deer lease and farm (Longview Texas). Last time registered was 1981. Already found many issues to deal with, but not sure yet about electrical. Most electrical stuff seems to work. Engine not yet ready to run. PO had 2 barrel pumper mounted on to 4 barrel holley intake with homeade adapter plate. 1/4" steel plate cut with torch...badly warped with 3/4" of gasket sealer. Doubtful then it sealed.

What is best carb to go back with on this engine...2bb or 4bb?

Hopefull I can work out all issues eventually. Only paid $500 for rig so hopefully didn't loose any money on deal.
P1010023.webp
 
2 bbl vs 4 bbl.

A 2bbl is cheaper for OEMs to make/purchase/install, and it is easier for aftermarket users to set up. Easier because you have no secondaries to set up and tune.

If a PROPERLY SIZED 4-bbl is used, it can give better throttle response and better fuel economy than a 2-bbl, because the primaries are smaller and fuel atomization is better.

The problem is, most people go for carbs that are way too big for their applications, and will never make use of the CFM flow rating. The result is poor fuel economy. As an example, the Holley 470 cfm truck avenger carb is a far better choice for most smallblock applications in 4x4's than the 670 cfm model, because very few 4x4's ever see WOT (Wide Open Throttle) other than mudders. But gee, the 670 and 770 are OBVIOUSLY "much better" for performance because they are "bigger", right? Well, no, wrong. The smaller carbs will give much better off idle and low rpm throttle response. The benefits should be obvious to rock crawlers and other 4x4 users who aren't into pure WOT power for mud bogging. For highway use, the higher you can get the air velocity through the carb without opening the secondaries, the better. A heavier secondary spring helps, or use of the tunable secondary housing with the rotary knob works.
 
BTW, I'm mainly referring to stock engines or engines with so-called "RV cams". If you have a hot rodded engine, with a high lift, long duration profile with lots of overlap, and big valves, then you can make use of a bigger carb. But then you probably aren't worried about fuel economy or low end throttle response either.
 
brian has the right ide to start with. but from looking at your photo, you have high rpm manifold on there now. this will not work worth a darn. your best bet ,imo, is standard chevy 4b manifold or something like a edelbrok 2101 performer. top it with a 4bbl rochester. this carb only flows like 300 while the primaries and 750 if you goose it. conversly, a rochester 2 bbl is a compromise ,with about 500 cfm at all positions.

have fun jim:)
 
hey dog,
thanks for the peek at your 283...i am running a rochester 2 barrel...my intake looks to be stock for the engine...it runs nice and has lots of power...i will post up a pic of our 283...hey does yours have power steering?....if so i would like a close up of the set up...we are getting ready to add power steering...need to replace my harmonic balancer, starting to wobble...sooo when i do that i am installing a double pulley to run to power steering pump...good luck with the truck

osagecruiser
 
Yea it looks like you have some form of tunnel-ram intake there - exactly what you don't want for low-rpm torque. I'd suggest looking at replacing it with a torquer or some form or RV intake manifold, coupled with a quadrajet or other spread-bore type 4 barrel carb.
 
Hey osage, no power steering. I'll be coming back to you later on how you did your. I will probably add in future. Not sure all the steps involved in adding power steering. I may talk to you off line sometime about details...

My64fj..... yes, i just removed the master cylinder over the weekend for cleaning and inspection....maybe dumb question about master cylinders..Of course the bowls were dry, but still fluid in lines. The front bowl had the screen /membrane disk(I don't know) stuck in the bottom of the bowl. Had to remove with pliers. The back brake bowl had the same screen/membrane disk stuck in the top (right below the cap). Which is correct position top or bottom.

Also the clutch master cylinder has a true looking float in in. It is black and surely acts as float, but no screen (membrane) in bowl. Does this description sound accurate for OEM?

If what I am writing doesn't make sense I'll post pics in new thread.

thanks...
 
Hey crusher, your loosing me on your terminology.. what's a tunnel ram? Just a high volume manifold???

So exactly what would be the best intake to look for?

Just went outside to look for markings on this one...it a holley with words Street Dominator embossed on the top right behind the oil filler neck.

When I removed the thermostat housing, I found the intake full of jelled sludge and antifreeze. I'm guessing the Al housing didn't fare very well during it's 20 year park under the shade tree. I'm sure the manifold is crap anyway.
 
dog,
i am gonna document the power steering install with pics...i think there is one documented with great photos...maybe by romer not for sure....the diff is he did'nt have a v-8, he did the mini truck install wich is what i'am doing....i have been assembling the parts and hope to have it done for our club event in september..get flat nasty with tornado alley cruisers..i would be happy to visit off line and answer any questions i can...there are some very knowledgable folk here on the board who have helped me ALOT!

osagecruiser
 
That intake manifold was a good piece for a street machine but, as noted by others, not so good for a low rev application like a Cruiser. A stock intake or Edelbrock Performer intake would be my choice. Stock intakes are REALLY cheap or free used while the Performer usually runs $50 at a swap meet used.

HTH,
Nick
 
Here are some specific examples of intakes suitable for a mild or "RV cammed" smallblock...

http://www.holley.com/300-48.asp Holley Street Dominator. This is a dual plane mainifold. It is a high rise design, but the power band is idle to 6000 rpm, which is ideal for most 4x4 applications. The recommended base carb is 600 cfm, so stepping down to a 470 Truck Avenger would probably be ideal for a 283, though a non-smog 600 cfm would be better from a pure street standpoint. (The Truck Avenger is better for off roading.) This intake will only work with square flange carbs ie non-spread bore Holley pattern. It's also 50-state legal including California C.A.R.B. HEI distributors will clear.

http://www.holley.com/8000.asp Weiand makes an Action Plus dual plane manifold with a power band from idle to 6000 rpm. It's designed for spread bore carbs, but can be used with square flange Holleys with adaptor plates. This manifold is also 50 state legal including C.A.R.B. HEI will clear. It's designed for 500 to 600 cfm carbs for stock use, larger for competition. Might be ideal with a small carb for the 283.

http://www.edelbrock.com/automotive_new/mc/manifolds/chevy_sb_perf.shtml Here's the Edelbrock Performer series. The best choice is probably the 2101 with a spread bore carb or an adaptor plate for a square bore carb (Holley). It will clear HEI.

Offenhauser might still make their Dual Port 360 Degree manifolds. These are a unique variation on the dual plane. The primaries and secondaries are totally divided. The primaries feed all 8 cylinders, with each primary barrel feeding 4 cylinders. The secondaries do the same. The meet at the port. The primaries feed in at the bottom of the port, and the secondaries at the top of the port. The port is offset, with the secondaries taking up a little more room. This gives much smaller primary runners for better off-idle throttle response, yet the secondaries are there for nearly full flow, minus the slight loss from the port divider. For a stock or mildly hotrodded 283 this wouldn't be noticable. Not very many places carried these manifolds. The last I knew of was PAW (Performance Automotive Warehouse). P/N's are OFF-6007-DP for square carbs (std Holley pattern) and OFF-6008-DP for spread bore pattern. They come without the oil hole in the manifold, but can be custom ordered with it at no charge, at least acording to my old catalog. It should be low enough to clear HEI, but no mention is made of that.
 
Last edited:
Mine's not this clean anymore but still a late 60's 283 built by the previous owner, supposedly taken out of a 68 Impala station wagon.

Ultradyne RV cam, .40 over 10:1 flat top pistons, 327 powerpack heads, edelbrock semi-hi-rise intake. It had a Holley when I bought it but changed to a Edelbrock 550 cfm. It still runs a little rich and I too would like to see a power steering setup on one of these :cool:
LC32.webp
 
Deep South Cruisers said:
Mine's not this clean anymore but still a late 60's 283 built by the previous owner, supposedly taken out of a 68 Impala station wagon.

Ultradyne RV cam, .40 over 10:1 flat top pistons, 327 powerpack heads, edelbrock semi-hi-rise intake. It had a Holley when I bought it but changed to a Edelbrock 550 cfm. It still runs a little rich and I too would like to see a power steering setup on one of these :cool:

I see from the pic you have overthe frame headers. Mini truck powersteering will not work on vehicles with those headers. The #5 exhaust tube goes directly over the return line. NO room for the fitting of hose. The only steering that will fit with over the frame are Scout, Astro Fj60 or traditional saginaw in the front
 
Those headers HAVE to go, I'm so tired of eating exhaust. The rest of the system is garbage anyway. I hope to go with block huggers but I'm pretty sure I'd have to swap to a mini-starter and my current starter is brand new so I
havent wanted to mess with it.

I dont even have a harmonic balancer, not sure why. The previous owner always talked about how broke he was but he managed to get some quality pieces in there. High volume oil pump, dual roller timing set, HEI dist. ECT.

I still wish I had gone with a quadra-jet when I changed the carb. but like others here I was afraid it was too much CFM for the smaller V8.
 
Regarding the electrical. I would recommend gutting the original. A chevy wiring harness is $200 all the wires are identified connect them up and go. Otherwise you can have constant elect. problems on a pig that old.

Kerry "pig-daddy"
 
Wow, i thought it was only one running one of these damn engines. I have had sooo many issues with putting on power steering stering on this engine. Since my heads dont have those top threaded holes. i had to use a bracket that went to the bottom block. anybody have any pics of there power steering setups on the 283?

Shane
 
which carb?

Look for a 5 to 600 cfm holley 4bbl with vaccum secondaries.
Used this set up in my 57 Chev. back in the day and wasted losts of competition including dodge duster 340.s. The vaccum secondaries only open if you put your foot into it. the primaries if I remember correctly were the size of a quarter the secondaries about 2+ inches. I could get 25+ mpg. if I had the wife along, not so good when I let loose. Indicator used to go 1 1/2" past 120 mph I figure about 135mph. I would do the 283 cruiser if I did not have diesel

bill.
 
Back
Top Bottom