#2 Knock Sensor-Mittchell Manual

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Nov 5, 2006
Threads
404
Messages
1,234
I am debating whether to change out the #2 knock sensor ( I am getting a 330 code on the scan gauge)

Or having the shop do it since I need some other work anyway. After reading the posts in the archive, it looks like the kind of thing that could really burn up some time.

My shop uses Mitchell rather than Alldata. Does anybody have access to Mitchell to see if the time to R&R the #2 knock sensor in a 1995 is spec'd out?
 
I am debating whether to change out the #2 knock sensor ( I am getting a 330 code on the scan gauge)

Or having the shop do it since I need some other work anyway. After reading the posts in the archive, it looks like the kind of thing that could really burn up some time.

My shop uses Mitchell rather than Alldata. Does anybody have access to Mitchell to see if the time to R&R the #2 knock sensor in a 1995 is spec'd out?

I have OBD1... but had a continual Code 52 for the number one knock sensor.... I kept putting it off trying to do things that needed to be done anyway that could cause an issue with engine knock.... Yesterday as I was inspecting the wiring harness that goes down to the front sensors... I discovered that the wire for the #1 knock sensor was broken.... I repaired the wire and didnt have to pay a good 200 bucks for a new sensor. And the other stuff needed to be done anyway.

So maybe its just a wire or someting simple...:cheers:
 
My check engine light is on. I took my 1997 FZJ80 to the stealership to pull the codes. (lazy) I was given the advice to have "the knock sensor" replaced. $215.00 for the part plus a 100 bucks labor.

I really would like to save some money and replace myself. Are there 1 or 2 sensors for the 97?

: - donut crisis - : Back later.
 
My check engine light is on. I took my 1997 FZJ80 to the stealership to pull the codes. (lazy) I was given the advice to have "the knock sensor" replaced. $215.00 for the part plus a 100 bucks labor.

I really would like to save some money and replace myself. Are there 1 or 2 sensors for the 97?

: - donut crisis - : Back later.

2 sensors on the DS of the block. 1 is right under the oil filter (there abouts) and the other is near the #5-6 cylinders.

I think I have 4-5 knock sensor spares....

:eek:
 
2 sensors on the DS of the block. 1 is right under the oil filter (there abouts) and the other is near the #5-6 cylinders.

I think I have 4-5 knock sensor spares....

:eek:

Will you please sell me 2? I have been looking forever.

Is there a way to tell which one it is?
 
having a fault in the wiring is more common on the Knock sensor circuit.

i am currently dealing with a fault on both knock sensors after doing a HG. using my snap on troubleshooter, it said that a signal wire short to the shielded circuit is common.

unfortunatly i haven't had the time to diagnose the problem accurately, but common sense would tell me that messing with the wiring while removing the head would lead to a broken wire or shorted wire, and not two bad knock sensors.

just what i have experienced, may not be your solution.

from my experience with other manufactures, the knock sensors are unlikely to fail. some of the only vehicles i have replaced them on, there was as technical service bulletin, and everyone knew of the problem.
 
Well that makes sense. Any wiring problem is most likely related to the wire harness near the EGR valve. Those wires get cooked and if you move them around a lot such as during head removal, I can definately see a short would develope as the insulation wears away and two wires that weren't otherwise touching each, now are. I think this problem is fairly common with the 80 and the stupid way the wire harness is routed.

I've been lucky so far, but have wrapped the crap out of my wire harness with heat insulation.
 
Who is "they"?

I'd get a comparative price check with CruiserDan just to see what the competition is pricing these at.....

That said, these are pricey units.

Stealership quote = "they"

just because the code says #2 knock sensor fault, doesnt mean the sensor itself is bad.

i wish it did though!!!! that would make my job alot easier!

What other culprit could be the problem? Mine is the #1 Knock Sensor.
 
Back
Top Bottom