2" body lift

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Mar 24, 2006
Threads
18
Messages
117
Anybody out there running a 2" body lift? If you have one please let me know what else needs to be done (Rad lowering, linkages...). From reading around it looks like 1.5" will go in without modifications. Is that right?

Thanks,
Kyon
 
You won't need any additional mods but you should install Caster Correction Bushings. What kind of lift are you installing?
 
Body lift

Ummm... Body lift...
 
Okay...

Well, I figured a body lift was a bit cheaper than putting portal axles on :rolleyes:.

In reality I'm making room for the exhaust and sliders. I'll post that stuff up later this month.

Thanks for the, umm, input...

Kyon
 
OOPS . . . Silly me:o




I thought he meant suspension lift.
 
Plans

Okay George, you forced my hand. So here are the plans (at least a peak).

2" body lift as discussed
6" lift (custom longarm setup with integrated belly skid)
37s

blah, blah, blah...

Gotta start somewhere right?

Kyon
 
I'm starting to get the feeling that George doesn't like body lifts.


:idea:
 
Yup

Well, I want to run my slider mounts straight across to the frame rail so the body lift has to go on. I'd rather go without but....
 
For whatever reason many are opposed to body lifts. I'm not opposed to those that have used them and have solid reasons why they did not like them, that is their experience and opinions. I have George's 2" lift and I have not had any problems with it. It allows me to run a full 3" exhaust up and over the frame, my sliders are tucked up higher and I have had no adverse effects from the lift. To each their own I guess.
 
Here's a few...look close

normal_Damage00.JPG

normal_skid03.jpg

normal_TLC_129.JPG

normal_TLC_130.JPG
 
i did a 2" body lift on mine and never looked back, it took me about 5 hours to do

the good things about a body lift is

1. keep your center of gravity lower if ya having a massive lift (like 8" total) is a big benifit

2. its cheeper than going a bigger supention lift, im running 3" spring and 2" body so i didnt need to change break lines, panhard, new frnt and rear arms.

3. you can clear bigger tires if you go a 6"+2" body over a 8" spring lift because the bump stops will be lower on the 6+2 over the 8" because your lifting the body and there not moving

the only issue i had was that the rear bar needs lifting and thats a little bit tricky but i just went with a custom tube one any way

so any way heres a very good write up on a body lift i used it to do mine.

http://lbd.end0.net/
 
I have a 2" body lift on my 91. I can't help with the radiator as my is an engine conversion with alum radiator. But I would imagine that might be an issue. The steering rod in closer to the end of the spines. But still not an real issue. Couldn't you get away with 37s and just the 6" lift with out doing the body lift. I was running a 4" lift with 2" body an 37s. I lowered the bump stops and rubbing was minimal. I now run 40s with the 6" springs and 2" body. But I've hacked the fenders. I have not had any bad issues with the body lift. however the truck is a trail truck!
 
body lift

the only issue i had was that the rear bar needs lifting and thats a little bit tricky but i just went with a custom tube one any way

What rear bar are you referring to? Bumper?... No issues with the radiator?

Couldn't you get away with 37s and just the 6" lift with out doing the body lift.

Yes I could but like I said, I was trying to make room for the sliders and over frame exhaust.

Thanks for the input guys,
Kyon
 
Have you considered a 1" body lift and altering your cat-converter configuration?

Granted I have a '94 so the exhaust already goes over the frame but I went to one cat rotated flat. I went that route so I could mount my sliders directly to the frame similar to TiredIron to maintain a smooth undercarriage. All six mounts are straight to the frame.

slider install
 
Back
Top Bottom