sbc in fj40 exhaust

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

madoc1

madoc1

Joined
May 28, 2005
Threads
71
Messages
437
Location
spicewood,tx.
had a good day .wap meet in fredericksburg, tex. no toy stuff but a good time. picked up a pair of rams horn manifolds because the set up i have now has the pass. side exh. going out then under the frame.

anyway, does anyone know of a coating for cast iron that i can do at home that sticks? barbie paint? eastwood?

other question --i read on here or somewhere that walker made a crossover set up (under the oil pan).
does anyone know the part #? maybe it was discontinued, but there might be one floating around out there in ethernet.

thx jim:beer: :beer:
 
Part # visible in this photo :D

i got it thru partsamerica.com

$40 or so
Add the correct flanges and gaskets and Over $50 gets you free shipping!
Walker Crossover.webp
 
thx guys, that is just what i was looking for! have a good eve. jim
 
hey madoc1 eastwood does make a brush on coating and so does POR15 you might check there sites ? i dont know how well they work but just thought i would tell you.

good luck!
 
Stock mainfold

Will the work with the stock manifold?
It would solve my problem if the do.

Thanks
 
Last edited:
What are the proper rams horn manifolds for a fj40 - to use with the 66 crossover ? I,ve seen some that dump straight down and some that dump at an angle.
 
I have about 1200 miles on the Eastwood manifold paint. Holding up fine so far.
 
Same part number at NAPA (42087). Bought one a few weeks ago. $57
 
Yes

terrx said:
Same part number at NAPA (42087). Bought one a few weeks ago. $57
Click to expand...

But will they work with stock manifold???
 
the rams i picked up dump straight down.hope this correct. pretty sure it si. having a heck of a time getting old studs out. heat, pb, heat pb, and so it goes.

jim
 
ok. neat info. so how do i save a thread ? just like texicans. would realy like to save this info to reread later if you get my drift.

jim
 
madoc1 said:
ok. neat info. so how do i save a thread ? just like texicans. would realy like to save this info to reread later if you get my drift.

jim
Click to expand...

You can copy the Http:// info and paste it to a page that you can save.
You can even paste it to an email and send it to yourself.
 
copies

being no comp. expert as most can tell, i did finally get it into my docs. this after one bad try with no pics and printing all 16 pages. thanks for the help. now i just need to learn how to organize my docs. maybe i should take some of my bar time and enroll in a comp. class? :rolleyes: :beer: :beer:
 
maybe i should take some of my bar time and enroll in a comp. class? :rolleyes: :beer: :beer:[/QUOTE]

Let no get carried away now.
:doh:
 
You must log in or register to reply here.

Similar threads

Mark Jennings
SOR Stainless Exhaust
Replies
11
Views
2K
DesertFJ40
DesertFJ40
igotta40
How many FJ40s in your FJ40?
Replies
9
Views
812
Paul_A
Paul_A
EWheeler
SBC Rewiring Question
Replies
4
Views
894
EWheeler
EWheeler
cstav86
Heat Riser Bushing Exhaust Leak - Need a temporary fix
Replies
4
Views
308
mattressking
mattressking

Users who are viewing this thread

Total: 1 (members: 0, guests: 1)

Share this page

Back
Top Bottom