Recent content by Yorda

  1. Yorda

    Long time reader, first time poster..

    After all the bog was removed the lowest point in the door was about 13mm, I have never looked at other cruiser doors to see if they are bowed in or if they are perfectly flat, given there are no real supports in the door I would expect some dished in effect but how much would be considered...
  2. Yorda

    Long time reader, first time poster..

    I had the passenger side door off already so decided to strip it down, and do a preliminary rust unearthing. Initially the loose scaly rust made the door bottom look worse than it turned out to be. It still requires some major rust repair but not as bad as I first thought. I put a straight...
  3. Yorda

    Long time reader, first time poster..

    So this weekend I spent a day reorganising the garage space as things had started to get disorganised, and I basically had a goat track to move around on. I did'nt realise how much stuff I had accumulated over the years.
  4. Yorda

    Long time reader, first time poster..

    I had some time available so decide to remove the front drip rail, because of where it was smashed it had popped several of the spot welds on the side drip rail also. The front drip rail was rusted out and had rusted the roof edge where it attaches in a couple of small spots, the drip rail has...
  5. Yorda

    Long time reader, first time poster..

    I was convinced my only hope of putting a roof on the 45 meant a fibreglass replacement, I had been trying to find one in good condition for a long time. My old roof as you can see was pretty rusty. I picked up a roof this weekend, needs some work as it has the front corner smashed in and the...
  6. Yorda

    Long time reader, first time poster..

    This morning I pulled the front fender from the bin and gave it a quick wash before dunking the other end in the electrolyte, over all quite happy withe the results. I did not expect the paint to come away, just all the rust. Anywhere there was a stone chip, scratch or star in the paint and rust...
  7. Yorda

    Long time reader, first time poster..

    Looking at my front fenders I was trying to work out how to get the rust out of some of the corners that I cant get a wire wheel into, electrolysis seemed a good idea, but I did not have a container big enough to hold a fender... Early the next morning drinking coffee and looking out my house...
  8. Yorda

    Long time reader, first time poster..

    So the fight against rust NEVER ends... I have been trying to find ways which are cost effective (because i have a tight budget) and not so labour intensive. I have been wire wheeling a few rusty bracket but they never seen to get some of the deep, built up rust, as it just seems to turn in hard...
  9. Yorda

    FJ45 roof dimensions needed.

    Thank you, that is very much appreciated.
  10. Yorda

    FJ45 roof dimensions needed.

    Hi all, long story short my Fj45 roof is rusted out bad, I have just found a second hand roof for sale that needs some panel beating, but have to pick it up in a car and fit it in my trunk, I dont have the old roof with me to measure if it will fit in the trunk of my car, does someone know the...
  11. Yorda

    Build 1963 FJ45LP SWB Fixed Top "Sweet Simplicity"

    I am definitely interested to see how your floor would turn out with Raptor Liner if you you go that direction.
  12. Yorda

    Long time reader, first time poster..

    While the old sealer has played a large part in all the rust problems, as i dig around the rust holes I am trying to identify where and what caused the rust problem. The cowling sealer was crumbling but still hard to dig out in spots, I am thinking of cleaning the sealer gap with phosphoric...
  13. Yorda

    Long time reader, first time poster..

    This project is starting to get bigger and having it on the road for summer is now highly unlikely given my time and finances, but thats ok she sat patiently for ten years, whats a couple more. I priced up today the seals for the cab and for the main door seals Im currently looking at $1400+...
  14. Yorda

    Long time reader, first time poster..

    So in the need for some material for weld in patches I decided I will cannibalise the old roof. I cleaned up a piece with a paint strip wheel and it looks promising, if anything it will give me some pieces to practice on.
  15. Yorda

    Long time reader, first time poster..

    So today I pulled the windscreen frame off, the 1/2 impact pulled the screws out easily, I found one largish rust hole at the bottom, i have not pulled the glass out yet so hopefully there will be no surprises as there was no rust bubbles around it. I have not found a single seal that is...
Back
Top Bottom