Recent content by TheCndnCruiser

  1. TheCndnCruiser

    Alternator bracket help- Broken bolt🥺

    I had the exact same thing happen. I drilled through the bolt and ended up snapping my extractor as well…. My heart dropped as I felt it break. But after what felt like hours (and probably was) I ended up drilling through that and put in a bolt with a lock washer on the other end. A VERY tight...
  2. TheCndnCruiser

    Rear hatch and tailgate RUST repair!

    Glad it could help! And good luck with your future repairs!
  3. TheCndnCruiser

    Rust!! I might’ve made a mistake. (Thread)

    Take a look at some of the rust repair I did to my 100 - hope it give you some hope! https://forum.ih8mud.com/threads/rear-hatch-and-tailgate-rust-repair.1281087/
  4. TheCndnCruiser

    Rear hatch and tailgate RUST repair!

    Appreciate it! - 1) I used 22 gage metal. (I had thicker material sitting around my shop but was too thick so I got the following patch.) Worked perfect for me. Sheet Metal | Canadian Tire - https://www.canadiantire.ca/en/pdp/sheet-metal-0475780p.html Welder wire was .030 flux core. I ended...
  5. TheCndnCruiser

    Rear hatch and tailgate RUST repair!

    And finally, the finished product! Feel free to ask any questions or offer me any advice, always love to learn!
  6. TheCndnCruiser

    Rear hatch and tailgate RUST repair!

    Finally was the painting stage. Because as I pulled back the seams on the hatch, some of the paint on the front also chipped off so I had to re-paint part of the front (I used seam sealer to reseal the seams I pulled back) I just used the dupli-colour clear coat as well.
  7. TheCndnCruiser

    Rear hatch and tailgate RUST repair!

    This was probably the most satisfying and rewarding moment of the repair. Also, forgot to mention that I treated and prepped the inside of the hatch and the tailgate so rust doesn't start again where the welds were done. Was much easier on the tailgate as I could remove the inner panel, but...
  8. TheCndnCruiser

    Rear hatch and tailgate RUST repair!

    Once I was content with the welds and sealed any pinholes after the griding process with small tack welds, I started the Bondo stage/ priming stage! my plan was only to re-paint the section around the repair but I decided I may as well refinish the entire tailgate and fix other imperfections...
  9. TheCndnCruiser

    Rear hatch and tailgate RUST repair!

    The next stage was welding and grinding. Be sure to use proper procedures when welding sheet metal to avoid burning holes and warping the panel!
  10. TheCndnCruiser

    Rear hatch and tailgate RUST repair!

    This Next series of images was a little more tricky as I had to try and match the intricate lines and curves in the bottom hatch all while making sure to line up the cutouts for the lights! It is by no means perfect but was happy with the outcome.
  11. TheCndnCruiser

    Rear hatch and tailgate RUST repair!

    I actually did take a look down and around there and it seems to be good! However, the rocker panel near the rear wheel well is starting to rust:rolleyes:... but not too bad so ill save that for another time... just not too long, or else it will probably be gone knowing landcruisers.
  12. TheCndnCruiser

    Rear hatch and tailgate RUST repair!

    Once I had cut out all of the existing rust and exposed all of the rust hidden in the seam, I began the tedious work of cutting new pieces of sheet metal to weld into place (I used zinc-coated sheet metal and weld through primer to help prevent future rust as well) For the tailgate, I had to...
  13. TheCndnCruiser

    Rear hatch and tailgate RUST repair!

    Next, After tediously trying to work with the hatch on the truck, I decided it was too dang annoying so I removed it! Much Easier!! But, still was a lot of work to be done. The rust was mainly around those bottom license plate lights, but the bottom seam also had quite a bit of rust starting...
  14. TheCndnCruiser

    Rear hatch and tailgate RUST repair!

    The next stage was to grind out any parts containing rust! These are both tricky areas to repair as they are directly along the pinch seam so additional care was taken to remove the sections without damaging anything other parts of the body.
  15. TheCndnCruiser

    Rear hatch and tailgate RUST repair!

    These next pictures are after a little bit of wire wheeling to investigate the extent of the rust! (A wire wheel is quite abrasive, but my plan was to weld in new pieces anyway so didn't mind)
Back
Top Bottom