Recent content by tacupra

  1. tacupra

    Build 2JZ into 2001 4X4 Tacoma Build

    Marlin Crawler dual transfer case Taco Box decided to make an appearance as well.
  2. tacupra

    Build 2JZ into 2001 4X4 Tacoma Build

    The second EFR has arrived. EFR 9174 for the primary in the compound 2JZ setup. (Left: EFR 9174 Primary Right: EFR 7064 Secondary)
  3. tacupra

    Build 2JZ into 2001 4X4 Tacoma Build

    Imgur Album for testing fitment with cast manifold and quickspool valve with single EFR 7064. Click image to go to album:
  4. tacupra

    Build 2JZ into 2001 4X4 Tacoma Build

    Imgur Album for power steering and AC Lines. Click image to go to album:
  5. tacupra

    Build 2JZ into 2001 4X4 Tacoma Build

    Thanks man. The build has it's challenges and documenting adds more work, but if it helps anyone it is worthwhile! Imgur Album for Brake booster modification to fit 2JZ Intake Manifold. Click Image to go to Album:
  6. tacupra

    Build 2JZ into 2001 4X4 Tacoma Build

    I just wanted a platform that I can continue to build up if I got bored. Which I am glad I picked the 2JZ because it is an excellent Truck engine and responds so well to upgrades. The EFR 7064 I have on there now with a quick spool valve and super short intercooler plumbing (and water to air for...
  7. tacupra

    Build 2JZ into 2001 4X4 Tacoma Build

    Here is an imgur album with the oil cooler setup and electric pusher fans(It does keep the 2JZ Cool even in Hot Summer Days in Houston Traffic after pulling a loaded car hauler w/ AC on full blast):
  8. tacupra

    Build 2JZ into 2001 4X4 Tacoma Build

    Thanks bud! Also here is an imgur album with some of the intake plumbing including water to air intercooler plumbing:
  9. tacupra

    Build 2JZ into 2001 4X4 Tacoma Build

    Still can't seem to embed media or photos natively as the toolbar is grayed out. Here is an imgur album for some of the cooling system(Click image below):
  10. tacupra

    Build 2JZ into 2001 4X4 Tacoma Build

    Can't seem to post media content now. As the toolbar on top is grayed out. Will try later.
  11. tacupra

    Build 2JZ into 2001 4X4 Tacoma Build

    First time firing her up.
  12. tacupra

    Build 2JZ into 2001 4X4 Tacoma Build

    Here is some stuff you folks should like. Not in chronological order, but a good idea of how it looked when the initial 2JZ conversion was completed. Full res photo here
  13. tacupra

    Build 2JZ into 2001 4X4 Tacoma Build

    Now time for the transmission mount: Measuring the original length of the driveshaft to verify my total length after the cut. This point is the mounting flange at the front of the carrier bearing. The R154 bellhousing was bolted to the R150F and the transmission crossmember was modified...
  14. tacupra

    Build 2JZ into 2001 4X4 Tacoma Build

    Here is the drivers side engine mount flange. 1.75" Hole saw to match the bushing size. Start of the notch for the bushings After taking measurements with the reliefs on the bushings I cut the 1/4" stock to length. Test fitment of first plates. Test fitments of second plates...
  15. tacupra

    Build 2JZ into 2001 4X4 Tacoma Build

    Tracing Tacoma Frame Side Motor Mount The R154 bellhousing was bolted to the R150F and the transmission crossmember was modified (pushing the full engine/trans assembly back 2-3.4"). The water pump pulley is VERY close to the radiator. Tacoma Frame Side Motor Mount Flange after cutting trace...
Back
Top Bottom