Recent content by raisinhell2

  1. raisinhell2

    Build Mini P Our new shop rig

    Dynamatt in ... Boy how I hate doing this stuff. going to be a small intermission on posts . I have to go in for emergency surgery in the am . they have to fuse the joints on my big toe . Getting old sucks !!! I should be back at it late Dec !!!!!!!!!!!!!! Ho[e everyone east too much for...
  2. raisinhell2

    SAS SAS #10 Official Page 8/03/26-8/07/26

    Was looking for a picture and ran across this !! Terry you are missed my brother .
  3. raisinhell2

    Build Mini P Our new shop rig

    I use a epoxy based paint for the chassis on the final coat ..
  4. raisinhell2

    Build Mini P Our new shop rig

    Chassis is almost DONE!! This build is really starting to come together, and we're not cutting corners! Dobinsons 3.5-inch long-travel MRR lift with HD steering stabilizer. SUMO knuckle kit with Koyo wheel bearings, front and rear. All-new Toyota hardware to keep everything tight and prevent...
  5. raisinhell2

    Build Mini P Our new shop rig

    HUB PORN?????????????? Not really! This is just how we do EVERY knuckle .Almost every knuckle job we do gets all-new hardware. Why? Because the details matter! It amazes me how many people in this industry seem to have a problem using a torque wrench. There's a reason Toyota has torque specs...
  6. raisinhell2

    Build Mini P Our new shop rig

    Some revolution Gears . 5:29s on Factory lockers. Haven't decided 100% yet on tire size . 37s or 40s . Guess I better make up my mind soon . If I go 37s I will Just rebuilt the t case with the crawler gears . If I go 40's Ill do under-drive gears on the high side as well. Just not sure...
  7. raisinhell2

    November Trail Ride: China Wall, 11/14/2026 (EDITED)

    Dave here is the info for the Asian truck meet 9am to 11am at the caffeinated cow 1791 S 8th Street Unit G, Colorado Springs, CO, United States, 80905
  8. raisinhell2

    Build Mini P Our new shop rig

    Boring, I know................. The foundation of this rig is almost done . Brake lines are DONE!! It's the million little details that separate a good build from a GREAT build! Because when it comes to building Land Cruisers, **GOOD ENOUGH ISN'T GOOD ENOUGH!** I'm digging the drop on these...
  9. raisinhell2

    Non club run Rainbow falls Sat the 7th

    We are canceling this and will be joji9ng everyone the following week for china wall
  10. raisinhell2

    November Trail Ride: China Wall, 11/14/2026 (EDITED)

    I will be joining in on this .. Can I post this up on my business page and maybe a few local LC groups on FB . Maybe see if we can get some new people involved.
  11. raisinhell2

    Where is my coolant going?

    there is an o ring behind the timing cover that gets brittle and leaks . Ive seen this a few times on mystery coolant leaks. but 3 gallons ??
  12. raisinhell2

    Build Mini P Our new shop rig

    Yes ABS ( typo.). the LSPV suck. once you go over 35s they are pretty much worthless . I prefer consistent braking rather than having hardly any brakes when going down steep declines.
  13. raisinhell2

    Build Mini P Our new shop rig

    Naw Just threw some round stock in the lathe and whipped them up so i can put the sldier u bolts under the lines
  14. raisinhell2

    Build Mini P Our new shop rig

    Some new stainless steel brake lines and a ABS and LSVP delete. We tired making a new insulator mat for the firewall but we just couldn't get it to our liking so I lizard skinned the firewall
  15. raisinhell2

    Non club run Rainbow falls Sat the 7th

    Rainbow falls this Sat the 7th we will be leaving Rudys in COS at 930 a
Back
Top Bottom