Recent content by kiichiro

  1. kiichiro

    Where to wheel near West Chester, PA?

    Got it - thx!
  2. kiichiro

    Where to wheel near West Chester, PA?

    Thanks! On the "lower experience" side of the spectrum - not a seasoned vet but learning. Have been on half a dozen trips and took a 2 day training course with Overland Experts (but I'm finding there is no substitute for "on the job training"). Only one wheeling trip has involved significant...
  3. kiichiro

    Planning to do knuckle rebuild in March... HAMOM (Charlotte) or should I tacklet this myself?

    haha, i may have to buy another one! i didn't frame mine right away and now i've basically ruined it by putting creases in it and covering it with grease.... your poster framing game is strong!
  4. kiichiro

    Where to wheel near West Chester, PA?

    Hi Keystone crew - I'm visiting the area from NC in early May. Can any of you locals recommend a place I can wheel with my rig? I'm not towing it so it needs to be somewhat tame.... thx!
  5. kiichiro

    Planning to do knuckle rebuild in March... HAMOM (Charlotte) or should I tacklet this myself?

    That looks great! Love your rig - glad I could be a part of the project.
  6. kiichiro

    Parting Out Lehi, Utah ***Updated 93-97 FJ80's and LX450

    https://forum.ih8mud.com/threads/broken-power-steering-stud.738874/ check that out. think - repeat, think - p/n is 90901-26001. One of mine was boogered up and I replaced it. think it was only 3-4 bucks new.
  7. kiichiro

    80 series spindle bushing uneven wear on one side

    sorry for slow reply - i'm still learning how to use his forum. i didn't think anyone responded! ugh... i looked at your old post. My wear is all on the inner diameter. i did a full axle job - very methodical / neurotic. i started wondering if i did something that put the axle in an...
  8. kiichiro

    Parting Out Lehi, Utah ***Updated 93-97 FJ80's and LX450

    looking for "Plate, Rear Floor Mat, No.1", Toyota P/N 58625-60010-03. This is a brown plastic piece just inside the passenger rear door on floor next to 2nd row seat. Held on by two plastic screws but I don't need those, just the step plate with the "tread" pattern on it. Again, passenger...
  9. kiichiro

    80 series spindle bushing uneven wear on one side

    Anyone know why I would have significant wear on one side of my spindle bushing on one side of the axle? I have read about a knuckle centering tool but I only see that is needed if the knuckle is not original? Is it possible my axle is so off-center that I need to re-shim that knuckle? I...
  10. kiichiro

    Planning to do knuckle rebuild in March... HAMOM (Charlotte) or should I tacklet this myself?

    I'm in CLT and I did this last summer on my 97 (new everything - axles, bearings, spindle bushings, knuckle / flange stud hardware, etc, etc, etc) - so I graduated past "staying at a Holiday Inn last night" but surely not as proficient as those that have multiple reps at the job. Watched OTRAMM...
  11. kiichiro

    SOLD Driver Side / Left Rear Door Flare / Moulding Rivet Brackets

    Found - thanks. No further assistance needed.
  12. kiichiro

    SOLD Driver Side / Left Rear Door Flare / Moulding Rivet Brackets

    Hi, need the two riveted metal brackets that hold the top and bottom of the curved part of the flare to the edge of the door on an 80 series - specifically a 1997 LX450 but I think those brackets may be the same for the Land Cruiser. Both are held on by two rivets each and I'd love guidance on...
Back
Top Bottom