Recent content by DamnFewLeft

  1. DamnFewLeft

    DFL’s ‘79 Build

    I have been going out to the cruiser to a dead battery. Takes about four days. I noticed that when it gets wet, the carb fan will short and run at weird times. It’d be on randomly two days after I drove it. So I unplugged it. Then it snowed a ton where I live over the last 24hrs. As a result I...
  2. DamnFewLeft

    DFL’s ‘79 Build

    Well... it’s not the fluid. It might have been bog water, but it was compressible. Stuff floating on the top is just new GL4 from the tube and is clearly less dense. But it gave me a chance to get the youngest out to the garage to help bleed the clutch so I don’t care what came of it!
  3. DamnFewLeft

    DFL’s ‘79 Build

    I have definitely wondered if it is the fluid. The stuff I purchased is not the Lucas stuff I ran before. Fluid swap is step two or three, and I’ll keep an eye out for Red Line. Thanks!
  4. DamnFewLeft

    DFL’s ‘79 Build

    I had noticed in my last moments of rebuilding that the two were pressed a bit tightly. Went back thru my photos and determined how the bearings sat in the case because I couldn’t get the tail to stop spinning in neutral. I drove the input toward the output to seat the output, then drove the...
  5. DamnFewLeft

    DFL’s ‘79 Build

    That’s what I’m hoping. The fluid resembles puddle water so it’s probably not incompressible anymore. Additionally, I noticed a bunch of muck in the bottom of the slave cylinder that could be limiting the travel of the piston, but I opted to do nothing until I bled the system.
  6. DamnFewLeft

    DFL’s ‘79 Build

    Question about 4 speed grinding. I have been driving it for about a month on and off. Now after the rebuild I have been experiencing some slight grinding especially on cold startup when I shift first to second and second to third. Fourth rarely has trouble finding teeth cleanly. Synchros are...
  7. DamnFewLeft

    DFL’s ‘79 Build

    That was my favorite album growing up so to find it in the rig on tape was insane! The paint is half original half primer. Well almost half primer But I love the off-white so I’ll probably rattle can it for now and do a nice two stage when it gets resto’d.
  8. DamnFewLeft

    DFL’s ‘79 Build

    Put in the trans/tcase. Painted the drive lines. Rolled it out on its own wheels. Back on the road and super excited!!
  9. DamnFewLeft

    DFL’s ‘79 Build

    I then replaced the RMC and oil pan gasket. If you can pull the oil pan, the RMC will slide right on. Also made sure the rear plugs are sealed. I added some sealant around them now because I’m doing an engine rebuild within the next 10k miles anyway. Popped in the new clutch from SOR after I got...
  10. DamnFewLeft

    DFL’s ‘79 Build

    Then I went at the 4 speed. I used a mix of this forum, SOR’s rebuild manual, and my brainy parts. Make sure you take lots of pictures of everything. I’ve read a great build thread on here where the poster had trouble determining how things were oriented. Just make sure that you also ensure...
  11. DamnFewLeft

    DFL’s ‘79 Build

    I did the tcase first. Bought a parts cleaner from HF and filled it with: Then power washed and chiseled out the grime. and ripped it all apart. Make sure you have bearing pullers and a bit of patience. I cleaned everything as it came off so I could store it and not get grime everywhere. I’ll...
  12. DamnFewLeft

    DFL’s ‘79 Build

    But then I noticed it started to bleed out a lot of fluids and I was certain I had pushed it too far. It sat for years and the seals dried out. When I ran it up to temp and put it to work over the summer it pushed it too far. The seal in the nose cone went, followed by the RMC and the pinion...
  13. DamnFewLeft

    DFL’s ‘79 Build

    And I drove it for about 1000 miles. It was glorious. Any chance I had to take it I would drive it. I have a brand new Ram that thinks for me, but that makes traffic boring. I found myself counting the stitches on my dash to keep occupied. NPR only does so much. But in the ‘79 it’s a different...
  14. DamnFewLeft

    DFL’s ‘79 Build

    I then polished up all the pulls. Simple technique. Clean it and pick out all the old paint. Fill the old embossed letters with new paint of your color choice. Then you can either polish with a wet towel or sand it with 600 grit. Buff it after the paint on the surface is gone. I used a...
  15. DamnFewLeft

    DFL’s ‘79 Build

    I also started cleaning up the dash. I started with the Choke cable. The end had frayed and couldn’t make it thru the hole to attach securely to the carb again so I decided to replace everything except the pull. The sheath was destroyed and the cable would get stuck. I yanked it all apart...
Back
Top Bottom