Recent content by bart007

  1. B

    Resurrected 80

    LOL, thanks, Im more of a Herd fan though but full on for the state of WV
  2. B

    Resurrected 80

    I cleaned up the rear old rear bumper and reinstalled it. Not my favorite but better than the Jeep bumper .
  3. B

    Binding at full lock when steering

    Yep, you are exactly right. I decided to check the front again before driving with the frt driveshaft removed. I jacked both wheels off the ground and turned one wheel only to see the other wheel going the same direction. Checked the transfer case and CDL switch again, no indicators showing a...
  4. B

    Binding at full lock when steering

    Replaced the P/S pump today with no changes to the steering. Still hard when turning, still easy when one wheel is off the ground. One thing I noticed is, when driving it wants to return to center almost too quickly. Like steering against straight line driving. If you lock the wheels to one...
  5. B

    Resurrected 80

    Ive run these bumpers for years on Jeeps with no issues. I just cant see spending the money they are asking for on these LC bumpers. Crazy expensive to say the least. I couldnt stand the looks of the JK bumper so I cut it off. Now to start over.
  6. B

    Resurrected 80

    I have a complete home built front bumper
  7. B

    Resurrected 80

    No problem, its hardly patched in, I used a Hobart Ironman 230 to burn it into the frame as well as making gussets from the frame to the rear bumper. Thats one of the reasons I will be dreading removing this thing. I checked 4x4 Labs and selected the DIY w/out swings outs and was ready to...
  8. B

    Resurrected 80

    Thanks, thats very close to where it was cut, thanks
  9. B

    Resurrected 80

    No sweat, not sure how much I like it, definitely didnt like the heavy POS that was on there before.
  10. B

    Resurrected 80

    Probably 4" but thats only what I cut, it may have been cut some before, not sure
  11. B

    Resurrected 80

    In the pursuit of trying to bring this 80 series back to life, I modified a JK Wrangler rear bumper to fit. It sits a bit low but will work until I decide to change it. Width wise, the outriggers are very close to the body. The frame mounts are about 1/4" away from the outer frame rails. I did...
  12. B

    Binding at full lock when steering

    Well, I checked my caster with a degree finder and both sides were right at 4 degrees which is about 3 degrees from where it should be, based on the lift. This should not affect the steering while sitting though. It will steer w/out binding when either wheel is off the ground, one at a time...
  13. B

    Binding at full lock when steering

    It has the triple lock function and I am assuming its unlocked, no indicator lights are on. I drove this about 5 miles after the tires with few issues, then I installed the offset castor bushings to get the return to center feel back in the steering. After the bushing install is when I noticed...
  14. B

    Binding at full lock when steering

    That was exactly my first impression, mostly due to the fact, when I raised one wheel off the ground, it would steer fine from lock to lock with no binding. I also noticed a bottle of P/S fluid stored in front of the battery and evidence of what looks like the P/S fluid leaking from the top...
  15. B

    Binding at full lock when steering

    Thanks for the response, I checked my castor with an angle gauge and at first quick glance assumed it was close. I will recheck today and spend more time with my readings. I read through that thread and was hoping I would not need a set of $1000.00 plus arms to get this right. I have not had...
Back
Top Bottom