Toyota emblems installation question (1 Viewer)

[eleblanc]

What drill size you use for 79 - 84 Toyota emblem

http://us.st11.yimg.com/us.st.yimg.com/I/coolfj40_1938_392696805

Last thing i want to do is make a hole too big.

any trick for the bolt patern? ink?

 

[exmodlad]

What bill size you use for 79 - 84 Toyota emblem

http://us.st11.yimg.com/us.st.yimg.com/I/coolfj40_1938_392696805

Last thing i want to do is make a hole too big.

any trick for the bolt patern? ink?

cut the tits off and glue them on..with a good RTV silicone...that way you have no holes for rust to start, that's what i did

best regards

Gord

 

[dfmorse]

Dam, thats a nice rear bumper set up

...

 

[eleblanc]

cut the tits off and glue them on..with a good RTV silicone...that way you have no holes for rust to start, that's what i did



best regards

Gord

Nice bumper, i like it.

 

[eleblanc]

Dam, thats a nice rear bumper set up

...

LOL, 1 min apart

 

[eleblanc]

RTV silicone...

Gord

Sorry for my ignorance but RTV stand for?

EL

 

[hatchman]

3M makes a two sided tape just for this purpose... you can find at any auto parts store.

 

[Colorado Boy-74-FJ40]

JB weld works really good too. I attached my fender emblems with it and it has lasted two years now.

 

[KOOTENAY KRUZER]

Sorry for my ignorance but RTV stand for?

EL

RTV stands for Room Temperature Vulcanizing. The product described is ordinary silicone sealer.

 

[exmodlad]

Dam, thats a nice rear bumper set up

...

Thanks very much...it kinda matches the front one, don't you think!!

Best Regards

Gord

**these are custom built bumpers built in my shop for a customers truck**

 

[eleblanc]

Thanks very much...it kinda matches the front one, don't you think!!



Best Regards

Gord

**these are custom built bumpers built in my shop for a customers truck**

Very very nice, steel and galvanised?

If your shackle are not upside down mine are...

 

[apeterson]

Very very nice, steel and galvanised?

If your shackle are not upside down mine are...

then yours are!

only know this because I had to change mine once!

 

[apeterson]

Thanks very much...it kinda matches the front one, don't you think!!

Best Regards

Gord

**these are custom built bumpers built in my shop for a customers truck**

Really cool!!! not to hijack but do you have a build thread going with your truck???? if not you should!

 

[eleblanc]

then yours are!

only know this because I had to change mine once!

Poste #25

https://forum.ih8mud.com/showthread.php?t=111215&highlight=ome+awesome

I'm checking with Arb, has i've seen too many opposing advise..

 

[apeterson]

Poste #25

https://forum.ih8mud.com/showthread.php?t=111215&highlight=ome+awesome

I'm checking with Arb, has i've seen too many opposing advise..

your front ones look correct... your rears look wrong... however I may be wrong.... let me know what you find out..

 

[eleblanc]

your front ones look correct... your rears look wrong... however I may be wrong.... let me know what you find out..

Here you go

https://forum.ih8mud.com/showthread.php?p=1986693#post1986693

 

[apeterson]

I stand corrected ..... I would never believed it however... it does makes senes if you think about it...

 

[exmodlad]

Here you go

https://forum.ih8mud.com/showthread.php?p=1986693#post1986693

Thanks for the info....when i bought the "BELTON" suspension kit, the fellow i bought it from, gave me a box of parts and a thank you for the cheque and that was it...there were no instructions at all, and i was not sure till now, how exactly the shackles were supposed to be oriented.

good thing its not to big a deal to change them over, dealing with suppliers in Canada is such a pain at time's cause they, save a few, never include instructions for the parts/goods you buy and they expect people to just "KNOW" how to put things together...

Thanks again

Best regards

Gord