Pretty quiet in here... what are you working on? (4 Viewers)

[Explorer4Hire]

Not yet. I will on completion. It’s not light. I am painting the drawer fronts black and using fuzzy side Velcro tape for the edges. I also need to fashion a strike plate for the paddles and get some right angle diamond plate or something for that top carpet edge.
I am gonna go to the dump and weigh in with and without it after I’m all finished. Top is 3/4, everything else is 1/2.

 

[Explorer4Hire]

Nearly done. Strike plates and diamond plate trim for the corner and it’s a wrap. I have to wait for my corner trim to arrive. I will post a final pic when mounted up with weight. See you guys at tech day!

 

[Stumpalama]

Removed a busted 6mm cap retaining bolt and replaced all the 6mm & 8mm bolts and retainers with new in an effort to prevent them from loosening again.

 

[Explorer4Hire]

Cleaning untold amounts of animal sh!7 off a very bad beagle.

 

[b4wheeler]

Finally got the lift on my truck. With help of Ryan, Steve , Steve and OTRAMM!

 

[b4wheeler]

Before and After (MD tags, for those that will ask)

 

[Explorer4Hire]

Nice!

 

[NearJetties]

New shackle bushings and new to me greasable OME shackles installed at shop day.

The ride quality improvement is amazing. No more feeling vibrations from cut up/rough pavement (like on 66 due to construction) and DC potholes through your teeth. And that’s with worn out autozone shocks.

 

[dbug]

I couldn’t make it to Tech Day, but was inspired by it and finally installed the grab bar I had lying around for a couple years.

 

[JohnVee]

^^^. I LOVE the towel holder in my ‘94 80!

 

[Von Hayek]

I couldn’t make it to Tech Day, but was inspired by it and finally installed the grab bar I had lying around for a couple years.

View attachment 1893158

Nifty.

 

[Explorer4Hire]

Changed my oil today and decided while I was out there I would remove the dumb steps from the rock rails.

Much better.

Though I have been eyeing some white knuckle sliders instead of building some myself. I like them.

 

[Crusha]

That ^ is a nice color for an FJC!

 

[1MOA]

I cleaned out my 40 repaired the rear heater fan ( it was literally full of mud) took the motor apart cleaned the contacts lightly sanded the armature and replaced the upper and lower felts and oil them and it spun right up.

Changed the oil, this is with about 110 miles on the oil and it is the first oil change since it sat for 21 years. I took a sample and sent it to blackstone labs. I am sure it wil be interesting. I found some “stuff” stuck to the drain plug and cleaned out the oil pan bottom. I’m surprised it was only the shmeg on the drain plug and not chunks of metal but we will see.

 

[Explorer4Hire]

That ^ is a nice color for an FJC!

Thanks! The ‘11 TRail Teams color scheme is my favorite. I looked hi and low for the 11 or 14 (iceberg). I like this the best though. I’d love a light blue pig or 40 though.

 

[Betteron2wheels]

Busy putting the smoke back into this 3d printer. Let it out working on an upgrade. Hopefully it'll be back to status quo

 

[JohnVee]

No pics because it's all boring stuff. I'm back home with the fleet in CLT and trying to do routine maintenance while it's warm outside. Replaced the wife's crunched up lift gate with a nice one of the same color today. Installed a new AutoZone Duralast Platinum AGM24 for my '96 LX. Hoping to rebuild and install a starter this weekend. Oil changes all around on Thursday. Rear brake pads on the '94 tomorrow followed by state inspection. Oh, and a little thing called driving the piss out of them while I can!!!

 

[Devilmans Hand]

Just filling the girlfriend's Jeep holes with my Toyota plugs.

 

[JohnVee]

@Devilmans Hand Now adapt a center cap for that spare.

 

[TLEX]

View attachment 1899389

Just filling the girlfriend's Jeep holes with my Toyota plugs.

Please tell me you picked up that dollar bill