Need to borrow a 1FZ-FE pulley holder (1 Viewer)

Joined
Mar 2, 2016
Messages
62
Location
Albany Oregon
Would anyone be willing to loan me their crank pulley holder for a 1fz-fe? The starter bump method won't budge it and neither will my 100lb air impact or 300ftlb electric impact guns.

I'm located in the California bay area, and I'm happy to pay you for your trouble shipping it out and back + a case of beer.

(Also OTRAM doesn't make these anymore, I've discovered through them.)
 

Comet

Knower of little, master of less.
SILVER Star
Joined
Nov 22, 2009
Messages
2,944
Location
Southwest Virginia
I welded and cut my own before OTRAMM was making them. Do you have a welder? I call mine the angry pigeon. It has been modified for a few different vehicles.
 

SNLC

OCD
Supporting Vendor
Joined
Sep 9, 2004
Messages
9,609
Location
Boise - Idaho
Website
www.snlandcruisers.com
Make one.

098D0BB8-A9D8-473D-93AC-6E935A01FB59.jpeg


Any steel supply shop or welding shop with a plasma cutter can knock this out for you fast and for cheap.

Cheers
 

Comet

Knower of little, master of less.
SILVER Star
Joined
Nov 22, 2009
Messages
2,944
Location
Southwest Virginia
Now I have to go find the angry pigeon. Pictures tomorrow, I hope.
 

CPACruiser

Supporting Vendor
SILVER Star
Joined
Jan 24, 2020
Messages
288
Location
PA
I make and distribute these now for anyone who wasn't aware. I keep a few of them in stock always. Just shipped a batch out yesterday. Thanks gents.

Cheers. 🤙🏼
 

Broski

I love Wheelin my 80
SILVER Star
Joined
Dec 3, 2015
Messages
4,543
Location
Morro Bay, At the edge of the Pacific ocean
Make one.

View attachment 3107993

Any steel supply shop or welding shop with a plasma cutter can knock this out for you fast and for cheap.

Cheers
I really doubt any shop can make a 1 off cheaper or faster then @CPACruiser as he has done all the leg work already and there ready to ship ;)
 

SNLC

OCD
Supporting Vendor
Joined
Sep 9, 2004
Messages
9,609
Location
Boise - Idaho
Website
www.snlandcruisers.com
I really doubt any shop can make a 1 off cheaper or faster then @CPACruiser as he has done all the leg work already and there ready to ship ;)


Well in my neighborhood I got several steel shops I could walk in with a piece of paper shaped how I needed. They would have it cut out in 20 minutes.

Cheers
 

Broski

I love Wheelin my 80
SILVER Star
Joined
Dec 3, 2015
Messages
4,543
Location
Morro Bay, At the edge of the Pacific ocean
Well in my neighborhood I got several steel shops I could walk in with a piece of paper shaped how I needed. They would have it cut out in 20 minutes.

Cheers
All I can say is your a lucky guy.
The rest of us don’t get that kink of service!!
 

SNLC

OCD
Supporting Vendor
Joined
Sep 9, 2004
Messages
9,609
Location
Boise - Idaho
Website
www.snlandcruisers.com
All I can say is your a lucky guy.
The rest of us don’t get that kink of service!!


I guess if you are in the country or there is no steel supply shop in your town. Even in a small town in Wyoming though we had a steel supply shop with a plasma table.

The one I pictured we whipped out down in Nicaragua. My buddy down there has a plasma cutter and cut it out by hand.

I am not knocking a made tool or borrowing the tool. I am saying if you are in a hurry it is not a hard tool to make. I think I have even used a standard generic harmonic balancer tool from Napa.

Cheers
 
Joined
Feb 13, 2013
Messages
87
I can send you the one I made (well I modified one made for a Subaru, but it worked quite well for me. I hope I never have to use it again. I'm about 250 miles north of you.
 
Joined
Jun 24, 2008
Messages
81
I have used a pipe wrench, with a rag stuck in the jaws, pushed into the pulley from the front and braced against the frame to remove/install crank bolts.Might be worth a try…
 

Broski

I love Wheelin my 80
SILVER Star
Joined
Dec 3, 2015
Messages
4,543
Location
Morro Bay, At the edge of the Pacific ocean
I guess if you are in the country or there is no steel supply shop in your town. Even in a small town in Wyoming though we had a steel supply shop with a plasma table.

The one I pictured we whipped out down in Nicaragua. My buddy down there has a plasma cutter and cut it out by hand.

I am not knocking a made tool or borrowing the tool. I am saying if you are in a hurry it is not a hard tool to make. I think I have even used a standard generic harmonic balancer tool from Napa.

Cheers
No offense intended, Really enjoy watching the builds you have going on and appreciate that you take the time to post.

The holder that PCA Cruier makes is CNC
Made and very nice for the price and I like to support mud venders.
It would cost me more in time and fuel just to go get the metal befor I got out the plasma cutter to start making the tool.
 

Comet

Knower of little, master of less.
SILVER Star
Joined
Nov 22, 2009
Messages
2,944
Location
Southwest Virginia
Man, you missed out on the “Angry Pigeon”.

6563BBEB-51A9-4E6E-AF3B-F79246493614.jpeg


Top is 80 series. Bottom is 100 series I think.
 

Comet

Knower of little, master of less.
SILVER Star
Joined
Nov 22, 2009
Messages
2,944
Location
Southwest Virginia
The diamond can kill when you bolt it to the engine.
 

Users who are viewing this thread

Top Bottom