Need help identifying the right part number (1 Viewer)

[enriquelaija]

I need to replace the locking hub in the right front, my vin is:

JT3HJ85JXV0151097​

I already bought one, but it does not fit, the shaft on my car did not fit

 

[leonard_nemoy]

I need to replace the locking hub in the right front, my vin is:

JT3HJ85JXV0151097​

I already bought one, but it does not fit, the shaft on my car did not fit


View attachment 3207253

Partsouq is a great resource. You can look at parts based off your Vin.

Link to all the powertrain schematics.

https://partsouq.com/en/catalog/genuine/vehicle?c=TOYOTA00&ssd=%24%2AKwH1wdDk86GluuqfsazroK25mZ6A8f7z8uD-zLzkteL95JvhsrLv5fzzvbmwqKfe666usuP65ZCIjby8rq614_rljJXw1tq08oyZlvf39PKuqbvl6uOjpOT74ampvfPy8eLr5KygvKqugZyL-PeK7ITQwMmMh-Ps5aCop7yqvroAAAAAkTZjmw%3D%3D%24&vid=0&cid=2&q=JT3HJ85JXV0151097

Here is a link to the front hub schematics, you should find what you need here.

https://partsouq.com/en/catalog/genuine/unit?c=TOYOTA00&ssd=%24%2AKwFAdGVRRhQQD18qBBleFRgMLCs1REtGR1VLeQlRAFdIUS5UBwdaUElGCAwGHRJrXhsRGhBXSEFYVE1MXVBJVkFBQ0dUBwdQHFFOVz8wP0MTEXpQDgoDGxc0DQlMTVBJViM7PVZaCUxKUElWPyZAPDwTEHMqJURER0JETxwHFVAQF1dIUUNPGhENQlFYVx8QVkwJY2M4S0Q5XzQ6Jm5ueFBfVhMbF1ZMGVgAAAAA6lCFxw%3D%3D%24&vid=0&cid=2&uid=384309&q=JT3HJ85JXV0151097

 

[enriquelaija]

Partsouq is a great resource. You can look at parts based off your Vin.

Link to all the powertrain schematics.

https://partsouq.com/en/catalog/genuine/vehicle?c=TOYOTA00&ssd=%24%2AKwH1wdDk86GluuqfsazroK25mZ6A8f7z8uD-zLzkteL95JvhsrLv5fzzvbmwqKfe666usuP65ZCIjby8rq614_rljJXw1tq08oyZlvf39PKuqbvl6uOjpOT74ampvfPy8eLr5KygvKqugZyL-PeK7ITQwMmMh-Ps5aCop7yqvroAAAAAkTZjmw%3D%3D%24&vid=0&cid=2&q=JT3HJ85JXV0151097

Here is a link to the front hub schematics, you should find what you need here.

https://partsouq.com/en/catalog/genuine/unit?c=TOYOTA00&ssd=%24%2AKwFAdGVRRhQQD18qBBleFRgMLCs1REtGR1VLeQlRAFdIUS5UBwdaUElGCAwGHRJrXhsRGhBXSEFYVE1MXVBJVkFBQ0dUBwdQHFFOVz8wP0MTEXpQDgoDGxc0DQlMTVBJViM7PVZaCUxKUElWPyZAPDwTEHMqJURER0JETxwHFVAQF1dIUUNPGhENQlFYVx8QVkwJY2M4S0Q5XzQ6Jm5ueFBfVhMbF1ZMGVgAAAAA6lCFxw%3D%3D%24&vid=0&cid=2&uid=384309&q=JT3HJ85JXV0151097

Thank you for your help, hope you have a prosperous new year

 

[sunrk]

AFAIK, the Aisin hubs for part-time 4wd config are all the same spec on 80's. Toyota part number 43530-60040 is the original part with two revisions I know of so the 43530-60042 is the one to source.

If your 80 is full-time 4wd you need drive flanges not Aisin hubs and there are two versions of those. The later one is bigger to accomadate an increased length to the outer CV joints.

 

[Kernal]

This might help:

Longs with Aisin hubs install

After doing some research, and deciding to go with Longs for replacement birfields, I went about trying to figure out how to install the Aisin hubs with the longer birfs. After several ideas and decided to go ahead and add another groove to match the location of the shorter earlier birfs. The...

forum.ih8mud.com