mini truck booster for fj40

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jul 26, 2008
Threads
1
Messages
2
Location
Vancouver, WA
Hello all this is my first post so go easy on me. My booster is bad in my 73 fj40. I read up here on mud and got some real good info but not crystal clear. It sounds like I can go to a junkyard and get a booster/master setup from a toyota truck for cheap and that that would be a direct replacement. Is this true? Any help would be much appreciated dont wanna pay five hundred for a new master.
 
yes some spacing of the actuator rod will be needed....you can get yours rebuilt @ Prior Reman. phone # 972-494-4254....or a 60 series will work as well.......
 
Hello all this is my first post so go easy on me. My booster is bad in my 73 fj40. I read up here on mud and got some real good info but not crystal clear. It sounds like I can go to a junkyard and get a booster/master setup from a toyota truck for cheap and that that would be a direct replacement. Is this true? Any help would be much appreciated dont wanna pay five hundred for a new master.

I got one off a 91 V6 mini truck from the pick and pull on 76th and Covington about 2 years ago. I got the booster and M/C for $45. It has been working great ever since. I had to shorten the pushrod about 1/2", but that was it. Fits and works perfect. Don't forget the check valve as it is external on a mini truck.

Good luck! :cheers:
 
what does it take to shorten the pushrod and what is the check valve?

1. A hacksaw or cutoff wheel. The pushrod is what attaches to the brake pedal. You have to cut a little bit off so that the brakes don't drag.
2. A one way valve that doesn't let the vacuum bleed out of the booster. It is the white valve in-line in the picture I attached.

Good luck! :cheers:
brake booster0002-1.webp
 
Hi All:

X2 what "FF LC Freak" wrote.

Regards,

Alan
----------------------------------------------------------------------------------
I got one off a 91 V6 mini truck from the pick and pull on 76th and Covington about 2 years ago. I got the booster and M/C for $45. It has been working great ever since. I had to shorten the pushrod about 1/2", but that was it. Fits and works perfect. Don't forget the check valve as it is external on a mini truck.

Good luck! :cheers:
 
I got one off a 91 V6 mini truck from the pick and pull on 76th and Covington about 2 years ago. I got the booster and M/C for $45. It has been working great ever since. I had to shorten the pushrod about 1/2", but that was it. Fits and works perfect. Don't forget the check valve as it is external on a mini truck.

Good luck! :cheers:

If you took both the booster and master off the same vehicle, why did you have to shorten the push rod?
 
Because there is more distance between the brake pedal and booster on a mini truck. That means the pushrod is longer. When you install it on a Landcruiser, with the brake pedal all the way up, it will still "engage" the booster. If you don't trim it down, your brakes will drag slightly. Clear as mud?

:cheers:
 
That's what I was thinking. I just figured out today that I need to replace both my master and booster. I have a lot of research ahead of me. Thanks for the info.
 
1. A hacksaw or cutoff wheel. The pushrod is what attaches to the brake pedal. You have to cut a little bit off so that the brakes don't drag.
2. A one way valve that doesn't let the vacuum bleed out of the booster. It is the white valve in-line in the picture I attached.

Good luck! :cheers:

Thanks to this post I just found out I've never had a check valve on mine since 1994 when I dumped the original cruiser booster. I got a valve out of a toy 4runner at the junk yard friday but need confirmation as to the direction of flow on the valve. It has an arrow and the letter "E". I suppose that means "Engine"...right?

EDIT: I checked the flow direction on it and it flows towards the engine...not towards the booster so I assume the "E" meant "engine".

ps I seem to talk to myself more on the internet :) Anyways, thanks for the tip on having a check valve. When my motor would quit my brakes required alot of foot power and this should help for about one or two pumps of the brake pedal.
 
Back
Top Bottom