Fuel injector specifications (1 Viewer)

[davisdrafting]

Would anyone know where I could find a spec
sheet on Denso injectors, specifically for MPI 3FE
#15513 (23250-61010)


I’ve already contacted Denso to no avail

 

[robbie]

Have you looked at a FSM? What kind of information are you looking for? robbie

 

[davisdrafting]

Looking for electrical spec’s such as min. max. volt,
currant, duty cycle, and recommend pulse duration
@ a given frequency. also fluid spec’s.

I have not received my FSM yet, “TIP” order a 92 FSM
if you own a 91 FJ80, you’ll save $50

I’m assembling a injector cleaning unit for personal usage.

 

[landtoy80]

<<<I’m assembling a injector cleaning unit for personal usage.>>>

I don't know what all the is about
BUT
I was thinkin of making/buying a homebrew injector cleaner too.
If you fig one out, post it as I have a 3fe and 1fz that needs cleaning.
Having them cleaned will go over $300 so if a system can be had for less than $300 I might get one.

 

[davisdrafting]

There are on vehicle injector cleaning kits but what I’ve read is they only
partially clean the injectors do to the amount of time the detergent lasts.

which is why I’m assembling an off vehicle cleaner so I can recycle
bio-clean or whatever detergent used.
It’s quite simple, electric fuel pump, regulator, small tank, some sort of fuel
rail setup or even hose an clamps and a power supply for the injector, not
to sure about the design of it until I see some specifications.
I’m guessing something like a pulse width modulation circuit using
a LM555 timer and power transistor or it could be as simple as wiring
a DPDT relay so that it pulses.

I plan on excluding the fuel pump and regulator, instead I will use air over fluid
(air compressor with onboard regulator) do to the lack of junkyards around here.

 

[landtank]

just drive the injectors through a HD flasher circuit. Oh and be sure to build a nice sonic bath utilizing your moma's 4d vibrator.

 

[woody]

Thanks to everyone for letting me waste 15 minutes of my morning cleaning up your childishness...

ON TOPIC - please....

 

[Beowulf]

How come you didn't slap Rick around? out:

-B-

 

[Scamper]

Will this affect my post count?

 

[semlin]

looks like you guys have effectively restored those lost posts.

 

[davisdrafting]

I think because whether it was derogatory or not it is useful input

 

[landtank]

How come you didn't slap Rick around? out:

-B-

I obiviously need to raise my game.

 

[Scamper]

I obiviously need to raise my game.

Slacker ...

 

[woody]

Thanks to everyone for letting me waste 15 minutes of my morning cleaning up your childishness...

ON TOPIC - please....

hhhhmmmmm

 

[landtank]

hhhhmmmmm

when designing a sonic cleaner, humming just isn't going to get the job done Woody!

 

[semlin]

humming works if you do it into a kazoo and touch the kazoo to the side of the sonic bath, but buzzing probably owrks better.

 

[Beowulf]

... utilizing your moma's 4d vibrator.

(How do you use that image that says "This thread is useless without pics" ? )

-B-

 

[Beowulf]

to ASSUME makes an ASS out of U-n-M

How did we ever get along without this purveyor of witty idioms?



-B-

 

[davisdrafting]

Did some searching and came up with a little info, not exactly what
I was looking for but it does look like only a 12v DC power source
is need to run the injectors due to the 13.8 ohm bobbin

Manufacturer: Nippon Denso
cc per minute: 213
Color: sky-blue
Ohms: 13.8
lbs per hour: 20.9
Est. hp. each: 42.6
Test Press. kpa: 290
Vehicles: TOYOTA
Engine: 3FE

 

[semlin]

is it just my browser or did woody disable quotes on this thread?