<Evil Laugh> - Beater build - </Evil Laugh>

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Mikesta

Never decruiserfied
SILVER Star
Joined
Jan 28, 2005
Threads
393
Messages
3,796
Location
Missouri
Website
www.showmerents.com
Well I needed a Trail rig and was going to build one ground up... but just couldn't pass this one up. Delivered last night on a rollback. Started right up with a gnarly sound. I had prior engagments so I garaged it and finally got to look at it some tonight.

- 350 Pontiac?
- New Skycrapper lift
- Dual? (front + rear) PTO that works great
- Front disk brakes
- Saginaw power steering setup
- Tilt steering wheel
- full cage
- Soft top
- 2 sets of soft doors
- Beat to crap 40 Body
IMG_6586.webp
IMG_6605.webp
IMG_6527.webp
 
Tonight. Drove it down the street with my 4yr old. He calls it a monster truck. That was fun.

Then after putting my 3 kids to bed went out to the garage and cleaned the interior and seats with some armorall... its pretty dirty still.

Walking around the tub... its pretty bashed in. Rockers.. busted, right side cown bent in.

Pulled the C drivers side door stop out. It was broken off the door and just haning there.

Then I took off the vent cover and Pulled out some "environment"... about 3 lbs.
IMG_6548.webp
IMG_6550.webp
IMG_6554.webp
 
Then crawled under the rig to see whats bolted to the engine.

1 3spd and 1 PTO.

At first glance I thought a rear drive shaft was missing.... then looking again noticed the that PTO has a rear plate for a rear PTO mount... or perhaps a rototiller. Never seen this before and I have a PTO on the bench that still needs rebuilding.
IMG_6557.webp
IMG_6559.webp
IMG_6560.webp
 
Then pulled my laptop into the garage and researched how to figure out what I have for an engine. The guy said 350 Pontiac. So I googled that and they say the numbers should be near the dist hole. I cleaned about 6oz of cake off and couldnt find anything.

Do you know what I have?
IMG_6573.webp
IMG_6575.webp
IMG_6577.webp
 
pto

I have a 3 speed like yours in my 71, I found some info and ads that said you could use it to hook up a winch compressor circular saw etc I even saw some rigs that looked as if they were running a scissors lift

I wondered if it could be used for onboard air. I plan on looking into tractor supply some more and see what I can find to put it to use
 
Saw this 40 on Craigslist a few times, looks like it will turn out as a really nice trail rig with a little elbow grease! Have fun-let me know if there is anything I can do for ya down south
 
Distributor Location

"BUICK"........Front-mounted distributor (only GM V-8 other than Caddy).....Cast aluminum front cover with external oil pump ........
 
Ch. Ch. Ch. Chia Vent

It's all the rage, The new chia vent. Just add water and in 2 to 3 weeks your vent will grow a full head of hair
chia.webp
 
Nice score!! I want a Buick V8... for my LeSabre :D I like the rig, looks like a hella ton of fun!!

Brian
 
3spd and 1 PTO.

At first glance I thought a rear drive shaft was missing.... then looking again noticed the that PTO has a rear plate for a rear PTO mount... or perhaps a rototiller. Never seen this before and I have a PTO on the bench that still needs rebuilding.



The one on your bench must be a later four speed unit, as I have only seen PTO boxes on three speeds that look identical to what you have...

It is probably single direction only as well...


Nice Land Cruiser.


:beer:
 
Nice cruiser, should be a good start. Any plans for your extra soft doors? Im looking for a set.
 
Nice cruiser, should be a good start. Any plans for your extra soft doors? Im looking for a set.

Your first in line once I figure it all out.
 
ch ch ch chia... tonight I do nothing but call it what it is.
 
thats the coolest thing i have ever seen. love the chia vent. i want one
 
Hi All:

Mikesta! You have two 40s in what, two weeks?!? :D

Congrats, that looks to be a good starting platform for a 'wheeler!

The engine is definitely not a Chevy V-8 (distributor would be by the firewall.) An SM420 would be a easy swap from the J30 three speed and give you crawl and more strength. The springs appear to need some adjusting (the shackle ankle is awful!) Looks like Mud Kings on ten inch aluminum wheels, no?

Let me know what I can do to help you get it on to the trail! :beer:

Regards,

Alan
 
Well, I need to slap a clutch in it. Know where I can get one this weekend? Thats my goal for tomorrow... Sunday is shot. Tor might have a decent used one. That and changing/checking fluids this weekend will be my goal. (also need to rebuild the Holley mopar carb).

Looks like the soonest I can get out to play would be Februrary 9th. I'll test the freeway driving this next week.

Hi All:

Mikesta! You have two 40s in what, two weeks?!? :D

Congrats, that looks to be a good starting platform for a 'wheeler!

The engine is definitely not a Chevy V-8 (distributor would be by the firewall.) An SM420 would be a easy swap from the J30 three speed and give you crawl and more strength. The springs appear to need some adjusting (the shackle ankle is awful!) Looks like Mud Kings on ten inch aluminum wheels, no?

Let me know what I can do to help you get it on to the trail! :beer:

Regards,

Alan
 
Back
Top Bottom