Builds DINGO- 60FZJ-UTE LS3 EROD (PROVEN CA SMOG) (1 Viewer)

[TRAIL TAILOR]

Finally getting to finish the interior and misc electrical goodies. A few more good days and all done.

J

 

[GW Nugget]

Nowdays a 1980s Cali smog vehicle is dam near impossible to install a motor & be legal.
I dont know what loophole or wording etc. how its done, but when it's my turn I'm going the Trail Tailor 5.3 route.

Not sure it needed a Cali plate to be legit!! Just saying!

 

[MoaByte]

Know days a 1980s Cali smog vehicle is dam near impossible to install a motor & be legal.
I dont know what loophole or wording etc. how its done, but when it's my turn I'm going the Trail Tailor 5.3 route.

I can only imagine the cool Land Cruisers we could have had without all that legislation. Diesels, V8's etc.

 

[kelly saad]

I have seen Dingo in person in the early stages, and it was AMAZING!! I hope to see it again someday finished. So cool.

 

[TRAIL TAILOR]

Cruise control activated!

Keyless entry and remote start up next.

J

 

[GW Nugget]

You forgot the "R" in Cruiser Control.
Super NICE build.

 

[Rockymtnreaper]

So cool J!

 

[TRAIL TAILOR]

A little more done.

Stereo sounds awesome. Love this JBL setup! Heated seats wired, push button start operational, 80 Tcase center lock switch and relay wired. A-pillar tweeters in, microphone in, remote door lock and alarm in, seat belts in, carpet in, amp fully wired and wires run for the dual sealed box JBL 10" woofers going into the rear console.

Will machine a matching tcase shifter knob in a couple weeks. Will make many of these for future builds as well to match the Lokar mushroom knobs.

Front and rear console will connect with a bridge-over so I can still lay longer items and my blackies in cases on the floor.

Will go to the headliner/upholstery shop in a few weeks when its my turn and get a custom "Starlight" headliner and back panel upholstery.




J

 

[sschruff]

All out & full tilt on this build. Design, specs, equipment, layout. . .absolutely love every single aspect. Nice work, J. . .wouldn't expect anything less!

Are you doing a front2rear console?

 

[TRAIL TAILOR]

Front console finalized and rear console/speaker box was CNC routered today and ready for assembly. (the spare 60 console pictured will be up for grabs soon)

J

 

[TRAIL TAILOR]

Rear console assembled and ready for initial fit up in the cab.

Would have done it this afternoon but the Stude frame set up took precedence....

J

52 STUDE

 

[TRAIL TAILOR]

Mushroom shifter knobs to match the Lokar knob are in process.

J

 

[Atwalz]

Mushroom shifter knobs to match the Lokar knob are in process.

J

View attachment 3223182

I want one of those for a high-low shifter for 80.

 

[TRAIL TAILOR]

I want one of those for a high-low shifter for 80.

I can make it happen. I can't remember is yours a polished or anodized black 6spd knob.

J

 

[Atwalz]

I can make it happen. I can't remember is yours a polished or anodized black 6spd knob.

J

 

[TRAIL TAILOR]

@Atwalz

Shifter knobs are in production.

Jason

 

[TRAIL TAILOR]

Consoles and my B-pillar seat belt covers are Genesis coated.

J

 

[TRAIL TAILOR]

Consoles are in. Need to finish the arm rests and tie in the speakers, USB-C and CB.

J

 

[spressomon]

What are the seats J?

 

[TRAIL TAILOR]

What are the seats J?

Corbeau