Cruiser finally saw its shadow...

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Jun 20, 2003
Threads
32
Messages
339
Location
Watertown, NY
Website
www.tonkacruiser.com
Here it is, finally saw the light of day after 1.5 months in a garage. I was really ready for it. It wasn't though. Had a power steering hose blow and one of the bolts mounting the steering ended up stripped. Once I got both of those problems fixed I was then able to pull it out and turn it without any problems. I even got to take it for a test drive to the end of the road and back without too many problems. I have a few items that are screaming for attention and I have 1.5 more days to work on it without any delays except for taking it to get exhaust put on.

Check list of things to do:
1. clean up front bumper ( had to rush it to get the plate on )
2. put custom tailgate on
3. get alternator working
4. clean up wire mess under dash
5. take water out of rad, seal it and put in new fluid
6. mount mirrors
7. do everything else I missed....

Chris

P.S. I'm finally out of the Cool Club (upside down besel)
 
lookin nice man
 
Ah, Yeah! And good job on the bezel. We gotta keep the pressure on Romer.
 
No pressure here Dave. Looks nice TonkaC!
 
hey tonk,

could you put a picture up of the rocker panel, just beside the fender?

i can't quite see what's actually goin on there.
i'm bout to chop the tail of my fenders off, so i'm lookin for ideas


thanks,
malphrus
 
in fact, he's a memeber of the upside-down bezel club if i remeber correctly
 
[quote author=me78he78 link=board=1;threadid=16277;start=msg156469#msg156469 date=1084482277]
romer likes his bezzel upside down?
[/quote]


I suspect he'll take it any way he can get it!


:D
 
Yes, I like my Bezel the way it is. If for nothing else, it gives Dave something to talk about. I see no reason to change it. After all, my cruiser has to make me happy, not the purists out there. I thought of changing my avitar to match the one I ues on Pirate, but then we wouldn't have as much fun.

You want to join my upsdie down Bezel club?

Sorry to lose you as a member TonkaC!

Ken
 
I do so enjoy teasing Ken about his bezel. I don't know what I'd do if he fixed it now! Probably go into a deep funk.
 
badass.
your tires are looking a little small now!
what size are those anyway? 235's? ;)
 
could you put a picture up of the rocker panel, just beside the fender?

i can't quite see what's actually goin on there.
i'm bout to chop the tail of my fenders off, so i'm lookin for ideas

I actually trimmed up the side panel above the floor line, the little post that extends down below the straight edge is where the pillar is and it only has an outside cover, not dual like the rest. I had to weld a piece back on to cover it so mud won't come in. I am planning on rock sliders that will cover the tab so it is not noticable.

chris

P.S. I sent you the full pic so you can get a better look.
 
The good news is I got the exhaust on and it sounds GREAT with the dual flowmasters. I do have to put a heat shield on my starter because it won't start after she has warmed up.

Bad news is I got the truck in the garage again tonight... Was trying to move the rear axle back. I made new rear spring mounts and they were done and on in less than 3 hours. I tried to pull the front ones off and again it beat me. I spent two hours and got them, but they didn't survive. I'm going to the metal shop tomorrow to get some steel to make new ones. Figure with all the fab work I've done I would have most steel I need.... NOT!

Thinks for the input, here are the new mounts, Chris
 
ha ha, good call bailey,

you gotta dig the boy wonder
 
Back
Top Bottom